Suzuki VZR1800 2007 страница 93 Скачать руководство пользователя

Страница: 93 / 609

3-36 ENGINE

VALVE GUIDE SERVICING

• Using the valve guide remover, drive the valve guide out

toward the intake or exhaust camshaft side.

09916-46020: Valve guide remover/installer

NOTE:
* Discard the removed valve guide subassemblies.
* Only oversized valve guides are available as replacement

parts. (Part No. 11115-65J00-001)

• Cool down the new valve guides in a freezer for about one

hour and heat the cylinder head to 100 – 150 °C (212 – 302
°F) with a hot plate.

• Apply engine oil to the valve guide hole.
• Drive the valve guide into the hole using the valve guide

installer

and attachment

09916-46020: Valve guide installer/remover

09916-44940: Attachment

NOTE:
Install the valve guide until the attachment contacts the cylinder
head

• After installing the valve guides, re-finish their guiding bores

using the reamer.

• Clean and oil the guides after reaming.

09916-37810: Valve guide reamer
09916-34542: Reamer handle

NOTE:
* Be sure to cool down the cylinder head to ambient air temper-

ature.

* Insert the reamer from the combustion chamber and always

turn the reamer handle clockwise.

Do not use a burner to heat the valve guide hole to
prevent cylinder head distortion.

Failure to oil the valve guide hole before driving the
new guide into place may result in a damaged guide or
head.

12.2 mm

(0.48 in)

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание VZR1800 2007

Отзывы:

Похожие инструкции для VZR1800 2007

Бренды по названию

Популярные бренды

Suzuki VZR1800 2007, Руководство по обслуживанию

Результаты поиска

Содержание VZR1800 2007

Отзывы:

Похожие инструкции для VZR1800 2007

Бренды по названию

Популярные бренды