manualshive.com logo in svg

Suzuki VZR1800 2007, Руководство по обслуживанию

Поделиться
Скачать
Suzuki VZR1800 2007 Скачать руководство пользователя страница 121

3-64     ENGINE

Inspection and cleaning

• Check the oil jets for clogging.
• Inspect the operation of the oil jet by pushing on the piston

with a proper bar

• If they are clogged or piston does not opreat, clean their oil

passage with a proper wire and compressed air or replace the
oil jet with a new one.

Installation

• Fit the new O-ring 

1

 to each piston cooling oil jet and apply

engine oil to them.

"

• Install each piston cooling oil jet with the bolt.

NOTE:
Apply a small quantity of THREAD LOCK to the bolts and tighten
them.

&

99000-32050: THREAD LOCK “1342” or equivalent

• Apply engine oil to the new O-ring 

2

 and 

3

.

"

• Install the oil jet.

2

 (for upper crankcase side)

3

 (for cylinder head side)

PLUG
Removal

• Remove the water jacket plugs 

1

 (for front and rear cylinder

head side).

Use the new O-rings to prevent oil pressure leak.

Use the new O-rings to prevent oil pressure leak.

Содержание VZR1800 2007


































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды