Suzuki SFV650 Скачать руководство пользователя страница 391

Страница: 391 / 573

Rear Suspension: 2C-4

2) Inspect the rear shock absorber for damage and oil

leakage, and absorber bushing for wear and
damage. If any defect is found, replace the rear
shock absorber with a new one.

CAUTION

Do not attempt to disassemble the rear shock
absorber. It is unserviceable.

3) Install the rear shock absorber. Refer to “Rear Shock

Absorber Removal and Installation (Page 2C-3)”.

Rear Suspension Adjustment

B944H12306006

After installing the rear suspension, adjust the spring
pre-load and damping force as follows.

Spring Pre-load Adjustment

Turn the spring Pre-load adjuster (1) to the desired
position.

NOTE
Position 1 provides the softest spring tension
and position 7 provides the stiffest.

STD position
3rd position

Rear Shock Absorber Disposal

B944H12306007

Refer to “Rear Shock Absorber Removal and Installation
(Page 2C-3)”.
The rear shock absorber unit contains high-pressure
nitrogen gas.

WARNING

• Mishandling can cause explosion.
• Keep away from fire and heat. High gas

pressure caused by heat can cause an
explosion.

• Release gas pressure before disposing.

Gas Pressure Release

Make sure to observe the following precautions.

WARNING

• Never apply heat or disassemble the

damper unit since it can explode or oil can
splash hazardously.

• When discarding the rear cushion unit, be

sure to release gas pressure from the unit
following the procedures.

1) Mark the drill center at the location “A” using a center

punch.

I944H1230007-01

I944H1230008-02

“a”: 7 mm (0.28 in)

“A”: Mark the drill hole

I944H1230009-02

“ a ”

“A”

I944H1230010-01

Содержание SFV650






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SFV650

Отзывы:

Похожие инструкции для SFV650

Бренды по названию

Популярные бренды

Suzuki SFV650, Руководство по обслуживанию

Результаты поиска

Содержание SFV650

Отзывы:

Похожие инструкции для SFV650

Бренды по названию

Популярные бренды