manualshive.com logo in svg

Suzuki SFV650, Руководство по обслуживанию


Поделиться
Скачать
background image

Table of Contents 4- i

4

Section 4

CONTENTS

Brake

Precautions .................................................4-1

Precautions............................................................. 4-1

Precautions for Brake System .............................. 4-1
Brake Fluid Information......................................... 4-1

Brake Control System and Diagnosis ... 4A-1

Schematic and Routing Diagram........................4A-1

Front Brake Hose Routing Diagram .................... 4A-1
Rear Brake Hose Routing Diagram..................... 4A-2

Diagnostic Information and Procedures............4A-3

Brake Symptom Diagnosis.................................. 4A-3

Repair Instructions ..............................................4A-4

Brake Pedal Height Inspection and 

Adjustment ........................................................ 4A-4

Front Brake Light Switch Inspection ................... 4A-4
Rear Brake Light Switch Inspection .................... 4A-4
Rear Brake Light Switch Inspection and 

Adjustment ........................................................ 4A-4

Brake Fluid Level Check ..................................... 4A-5
Brake Hose Inspection........................................ 4A-5
Air Bleeding from Brake Fluid Circuit .................. 4A-5
Brake Fluid Replacement.................................... 4A-6
Brake Hose Removal and Installation ................. 4A-8
Front Brake Master Cylinder Components.......... 4A-9
Front Brake Master Cylinder Assembly 

Removal and Installation................................. 4A-10

Front Brake Master Cylinder / Brake Lever 

Disassembly and Assembly ............................4A-11

Front Brake Master Cylinder Parts Inspection ..4A-12
Rear Brake Master Cylinder Components ........ 4A-13
Rear Brake Master Cylinder Assembly 

Removal and Installation................................. 4A-14

Rear Brake Master Cylinder Disassembly and 

Assembly ........................................................ 4A-15

Rear Brake Master Cylinder Parts Inspection ...4A-16

Specifications.....................................................4A-16

Service Data ..................................................... 4A-16
Tightening Torque Specifications......................4A-17

Special Tools and Equipment ...........................4A-17

Recommended Service Material .......................4A-17
Special Tool ......................................................4A-17

Front Brakes ............................................ 4B-1

Repair Instructions ..............................................4B-1

Front Brake Components ....................................4B-1
Front Brake Pad Inspection.................................4B-2
Front Brake Pad Replacement............................4B-2
Front Brake Caliper Removal and Installation.....4B-3
Front Brake Caliper Disassembly and 

Assembly...........................................................4B-4

Front Brake Caliper Parts Inspection ..................4B-6
Front Brake Disc Removal and Installation .........4B-6
Front Brake Disc Inspection ................................4B-7

Specifications.......................................................4B-8

Service Data........................................................4B-8
Tightening Torque Specifications........................4B-8

Special Tools and Equipment .............................4B-9

Recommended Service Material .........................4B-9
Special Tool ........................................................4B-9

Rear Brakes.............................................. 4C-1

Repair Instructions ..............................................4C-1

Rear Brake Components.....................................4C-1
Rear Brake Pad Inspection .................................4C-1
Rear Brake Pad Replacement ............................4C-2
Rear Brake Caliper Removal and Installation .....4C-3
Rear Brake Caliper Disassembly and 

Assembly...........................................................4C-4

Rear Brake Caliper Parts Inspection...................4C-5
Rear Brake Disc Removal and Installation..........4C-6
Rear Brake Disc Inspection.................................4C-7

Specifications.......................................................4C-8

Service Data........................................................4C-8
Tightening Torque Specifications........................4C-8

Special Tools and Equipment .............................4C-9

Recommended Service Material .........................4C-9
Special Tool ........................................................4C-9

Содержание SFV650






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SFV650

Dakota Digital VHX systems Operating Manual preview
VHX systems
Бренд: Dakota Digital Страницы: 6
Happy Trails KTM950 Quick Start Manual preview
KTM950
Бренд: Happy Trails Страницы: 4
VEB MZ ETZ 125 Operating Instructions Manual preview
MZ ETZ 125
Бренд: VEB Страницы: 63
Malaguti Grizzly Minicross RCX/12 50CC Service Manual preview
Grizzly Minicross RCX/12 50CC
Бренд: Malaguti Страницы: 33
Free Spirits 308927 Instructions Manual preview
308927
Бренд: Free Spirits Страницы: 28
SHERCO 2015 450 SEF-R Workshop Manual preview
2015 450 SEF-R
Бренд: SHERCO Страницы: 76
MRA 4025066152438 Mounting Instructions preview
4025066152438
Бренд: MRA Страницы: 8
hepco & becker Krauser 630.2516 Manual preview
Krauser 630.2516
Бренд: hepco & becker Страницы: 6
Denali LAH.07.10401 Instruction Manual preview
LAH.07.10401
Бренд: Denali Страницы: 2
KTM 690 SMC R 2016 Series Setup Instructions preview
690 SMC R 2016 Series
Бренд: KTM Страницы: 18
Yamaha NMAX 155 Owner'S Manual preview
NMAX 155
Бренд: Yamaha Страницы: 108
Yamaha FZS6V(C) Owner'S Manual preview
FZS6V(C)
Бренд: Yamaha Страницы: 100
IBEX 10007032 Mounting Instruction preview
10007032
Бренд: IBEX Страницы: 3
Leatt GPX Manual preview
GPX
Бренд: Leatt Страницы: 26
Leatt DBX 5.0 Owner'S Manual preview
DBX 5.0
Бренд: Leatt Страницы: 26
JAWA 1992 350/638 Workshop Manual preview
1992 350/638
Бренд: JAWA Страницы: 22
Orion AGB-21G Service Manual preview
AGB-21G
Бренд: Orion Страницы: 156
Benelli 302R Owner'S Manual preview
302R
Бренд: Benelli Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды