manualshive.com logo in svg

Suzuki SFV650, Руководство по обслуживанию


Поделиться
Скачать
background image

Table of Contents 9- i

9

Section 9

CONTENTS

Body and Accessories

Precautions .................................................9-1

Precautions............................................................. 9-1

Precautions for Electrical System ......................... 9-1

Component Location ............................................. 9-1

Electrical Components Location ........................... 9-1

Wiring Systems........................................ 9A-1

Schematic and Routing Diagram........................9A-1

Wiring Diagram ................................................... 9A-1
Wiring Harness Routing Diagram........................ 9A-5

Specifications.......................................................9A-9

Service Data ....................................................... 9A-9
Tightening Torque Specifications........................ 9A-9

Lighting Systems..................................... 9B-1

Repair Instructions ..............................................9B-1

Headlight Construction........................................ 9B-1
Headlight Cover Construction ............................. 9B-2
Headlight Removal and Installation .................... 9B-4
Headlight Bulb and Position Light Bulb 

Replacement..................................................... 9B-4

Headlight Beam Adjustment ............................... 9B-5
Rear Lighting System Construction..................... 9B-6
Rear Combination Light Components................. 9B-7
Rear Combination Light Removal and 

Installation......................................................... 9B-7

Rear Combination Light Bulb Replacement ........ 9B-8
License Plate Light Components ........................ 9B-9
License Plate Light Removal and Installation ..... 9B-9
License Plate Light Bulb Replacement .............9B-10
Front Turn Signal Light Construction ................9B-10
Turn Signal Light Components .........................9B-11
Front Turn Signal Light Removal and 

Installation.......................................................9B-11

Rear Turn Signal Light Removal and 

Installation.......................................................9B-12

Turn Signal Light Bulb Replacement ................9B-13
Turn Signal / Side-stand Relay Inspection ........ 9B-13
Turn Signal / Side-stand Relay Removal and 

Installation.......................................................9B-13

Hazard Switch Inspection ................................. 9B-13
Turn Signal Switch Inspection........................... 9B-14
Passing Light Switch Inspection ....................... 9B-14
Dimmer Switch Inspection................................. 9B-15

Specifications.....................................................9B-15

Service Data......................................................9B-15
Tightening Torque Specifications......................9B-15

Special Tools and Equipment ...........................9B-16

Special Tool ......................................................9B-16

Combination Meter / Fuel Meter / Horn.. 9C-1

General Description .............................................9C-1

Combination Meter System Description..............9C-1

Repair Instructions ..............................................9C-2

Combination Meter Components ........................9C-2
Combination Meter Removal and Installation .....9C-2
Combination Meter Disassembly and 

Assembly...........................................................9C-3

Combination Meter Inspection ............................9C-3
Engine Coolant Temperature Indicator Light 

Inspection..........................................................9C-4

Engine Coolant Temperature Removal and 

Installation .........................................................9C-4

Fuel Level Indicator Light Inspection...................9C-5
Fuel Level Gauge Inspection ..............................9C-5
Speedometer Inspection .....................................9C-5
Speed Sensor Removal and Installation .............9C-5
Speed Sensor Inspection ....................................9C-6
Oil Pressure Indicator Inspection ........................9C-6
Oil Pressure Switch Removal and Installation ....9C-7
Ignition Switch Inspection....................................9C-7
Ignition Switch Removal and Installation.............9C-7
Horn Inspection ...................................................9C-7
Horn Removal and Installation ............................9C-8

Specifications.......................................................9C-9

Service Data........................................................9C-9
Tightening Torque Specifications........................9C-9

Special Tools and Equipment .............................9C-9

Special Tool ........................................................9C-9

Exterior Parts ........................................... 9D-1

Schematic and Routing Diagram........................9D-1

Seat Lock Cable Routing Diagram......................9D-1

Repair Instructions ..............................................9D-2

Frame Cover Construction ..................................9D-2
Rear Fender Construction...................................9D-3
Fastener Removal and Installation......................9D-4
Exterior Parts Removal and Installation ..............9D-4

Special Tools and Equipment .............................9D-7

Содержание SFV650






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SFV650

Ducati 750 Sport Bevel Heaven Workshop Manual preview
750 Sport Bevel Heaven
Бренд: Ducati Страницы: 235
Bajaj Auto Avenger 150 Street Owner'S Manual preview
Avenger 150 Street
Бренд: Bajaj Auto Страницы: 40
Kabuto FR-1 Instruction Manual preview
FR-1
Бренд: Kabuto Страницы: 12
Dakota Digital MCL-36K-TCH Installation Manual preview
MCL-36K-TCH
Бренд: Dakota Digital Страницы: 6
Sym Joyride S 125i Owner'S Manual preview
Joyride S 125i
Бренд: Sym Страницы: 31
R&G CP0482 Fitting Instructions Manual preview
CP0482
Бренд: R&G Страницы: 18
LSL 377-810SW Manual preview
377-810SW
Бренд: LSL Страницы: 4
MV Agusta BRUTALE 750 ORO Workshop Manual preview
BRUTALE 750 ORO
Бренд: MV Agusta Страницы: 386
Garmin Montana 7 Series Installation Instructions Manual preview
Montana 7 Series
Бренд: Garmin Страницы: 24
Honeywell EV1 User'S Information Manual preview
EV1
Бренд: Honeywell Страницы: 8
Honeywell HW100 Important Instructions & Warnings preview
HW100
Бренд: Honeywell Страницы: 304
Shark Heritage Manual preview
Heritage
Бренд: Shark Страницы: 80
Arai GP-6S Operation Instructions preview
GP-6S
Бренд: Arai Страницы: 2
Happy Trails HTP1-8-30 Quick Start Manual preview
HTP1-8-30
Бренд: Happy Trails Страницы: 2
PIAGGIO MSS X9 EVOLUTION 250 Workshop Manual preview
MSS X9 EVOLUTION 250
Бренд: PIAGGIO Страницы: 262
PIAGGIO MP3 500 ie SPORT Business LT 2011 Manual preview
MP3 500 ie SPORT Business LT 2011
Бренд: PIAGGIO Страницы: 375
Ossa TR280i User Manual preview
TR280i
Бренд: Ossa Страницы: 72
APRILIA SCARABEO 300 SPECIAL Manual preview
SCARABEO 300 SPECIAL
Бренд: APRILIA Страницы: 157

Бренды по названию

Популярные бренды

Загрузить еще бренды