Suzuki SFV650 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 573

background image

Maintenance and Lubrication: 0B-13

WARNING

!

Do not open the radiator cap when the engine
is hot, as you may be injured by escaping hot
liquid or vapor. Engine coolant may be
harmful if swallowed or if it comes in contact
with skin or eyes. If engine coolant gets into
the eyes or in contact with the skin, flush
thoroughly with plenty of water. If swallowed,
induce vomiting and call physician
immediately.

1) Remove the right frame body cover. Refer to

“Exterior Parts Removal and Installation in Section
9D (Page 9D-4)”.

2) Remove the radiator cap (1).

3) Drain engine coolant by removing the drain bolt (2).

4) Flush the radiator with fresh water if necessary.
5) Tighten the drain plug (2) to the specified torque.

CAUTION

!

Replace the gasket with a new one.

Tightening torque
Engine coolant drain bolt (a): 13 N·m (1.3 kgf-m,
9.5 lbf-ft)

6) Pour the specified engine coolant up to the radiator

inlet.

Engine coolant capacity (excluding reservoir)
1 600 ml (1.7/1.4 US/Imp qt)

7) Bleed air from the cooling circuit.
8) After changing engine coolant, reinstall the removed

parts.

Air Bleeding From the Cooling Circuit

1) Support the motorcycle upright.
2) Remove the radiator cap and pour engine coolant up

to the radiator inlet. Refer to “Cooling System
Inspection (Page 0B-12)”.

3) Slowly swing the motorcycle, right and left, to bleed

the air trapped in the cooling circuit.

4) Add engine coolant up to the radiator inlet.
5) Start up the engine and bleed air from the radiator

inlet completely.

6) Add engine coolant up to the radiator inlet.
7) Repeat the 4), 5) procedures until no air bleeds from

the thermostat connector inlet.

8) Close the radiator cap securely.
9) After warming up and cooling down the engine

several times, add the engine coolant up to the full
level of the reservoir tank. Refer to “Cooling System
Inspection (Page 0B-12)”.

CAUTION

!

Make sure that the radiator is filled with
engine coolant up to the reservoir tank full
level.

1

I944H1160002-01

2

I944H1020032-01

(a)

2

I944H1020033-01

I944H1020034-01

«
...
37
38
39
40
41
...
»

Содержание SFV650






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SFV650

Бренд: Cannondale Страницы: 61

Бренд: GBRacing Страницы: 2

Бренд: N-Com Страницы: 36

Бренд: hepco & becker Страницы: 5

Бренд: SSR Motorsports Страницы: 39

Бренд: TRS Страницы: 38

Бренд: X-lite Страницы: 33

Бренд: DYNATEK Страницы: 7

Бренд: Arai Страницы: 2

Бренд: Yamaha Страницы: 93

Бренд: Yamaha Страницы: 114

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 74

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды