Suzuki SFV650 Скачать руководство пользователя страница 353

Страница: 353 / 573

Charging System: 1J-1

Engine

Charging System

Schematic and Routing Diagram

Charging System Diagram

B944H11A02001

Component Location

Charging System Components Location

B944H11A03001

Refer to “Electrical Components Location in Section 0A (Page 0A-7)”.

Diagnostic Information and Procedures

Charging System Symptom Diagnosis

B944H11A04001

SCR

Generator

Regulator/Rectifier

Ignition switch

Batter

Main fuse

Load

I944H11A0001-01

Condition

Possible cause

Correction / Reference Item

Generator does not
charge

Open- or short-circuited lead wires, or
loose lead connections.

Repair, replace or connect properly.

Short-circuited, grounded or open
generator coil.

Replace.

Short-circuited or punctured regulator/
rectifier.

Replace.

Generator does charge,
but charging rate is below
the specification

Lead wires tend to get short- or open-
circuited or loosely connected at
terminals.

Repair or retighten.

Grounded or open-circuited generator
coil.

Replace.

Defective regulator/rectifier.

Replace.

Defective cell plates in the battery.

Replace the battery.

Generator overcharges

Internal short-circuit in the battery.

Replace the battery.

Damaged or defective resistor element
in the regulator/rectifier.

Replace.

Poorly grounded regulator/rectifier.

Clean and tighten ground connection.

Unstable charging

Lead wire insulation frayed due to
vibration, resulting in intermittent short-
circuiting.

Repair or replace.

Internally short-circuited generator.

Replace.

Defective regulator/rectifier.

Replace.

Содержание SFV650






























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SFV650

Отзывы:

Похожие инструкции для SFV650

Бренды по названию

Популярные бренды

Suzuki SFV650, Руководство по обслуживанию

Результаты поиска

Содержание SFV650

Отзывы:

Похожие инструкции для SFV650

Бренды по названию

Популярные бренды