manualshive.com logo in svg

Suzuki SFV650, Руководство по обслуживанию


Поделиться
Скачать
background image

2D-16 Wheels and Tires: 

6) If the distance between the rim line and wheel rim 

varies, this indicates that the bead is not properly 
seated. If this is the case, deflate the tire completely 
and unseat the bead for both sides. Coat the bead 
with lubricant and fit the tire again.

7) When the bead has been fitted properly, adjust the 

pressure to specification.

8) As necessary, adjust the tire balance. Refer to 

“Wheel Balance Check and Adjustment (Page 2D-
17)”.

Cold inflation tire pressure

9) Install the mounting drum to the rear wheel. (For rear 

wheel) Refer to “Rear Wheel Dust Seal / Bearing 
Removal and Installation (Page 2D-13)”.

10) Install the wheel assembly. Refer to “Front Wheel 

Assembly Removal and Installation (Page 2D-4)” 
and “Rear Wheel Assembly Removal and Installation 
(Page 2D-11)”.

Wheel / Tire / Air Valve Inspection and Cleaning

B944H12406012

Refer to “Tire Removal and Installation (Page 2D-15)”.

Wheel

Wipe the wheel clean and check for the following points:
• Distortion and crack
• Any flaws and scratches at the bead seating area.
• Wheel rim runout. Refer to “Front Wheel Assembly 

Removal and Installation (Page 2D-4)” and “Rear 
Wheel Assembly Removal and Installation (Page 2D-
11)”.

Tire

Tire must be checked for the following points:
• Nick and rupture on side wall
• Tire tread depth (Refer to “Tire Inspection in Section 

0B (Page 0B-18)”.)

• Tread separation
• Abnormal, uneven wear on tread
• Surface damage on bead
• Localized tread wear due to skidding (Flat spot)
• Abnormal condition of inner liner

Air Valve

Inspect the air valve for peeling and damage. If any 
defect is found, replace the air valve with a new one. 
Refer to “Air Valve Removal and Installation (Page 2D-
17)”.

Inspect the valve core seal (1) for wear and damage. If 
any defect is found, replace the valve core with a new 
one. Refer to “Air Valve Removal and Installation 
(Page 2D-17)”.

Front

Rear

Solo riding

225 kPa

(2.25 kgf/cm

2

)

225 kPa

(2.25 kgf/cm

2

)

Dual riding

250 kPa

(2.50 kgf/cm

2

)

250 kPa

(2.50 kgf/cm

2

)

“B”

I649G1240040-02

I649G1240041-02

1. Seal

I649G1240042-02

I649G1240043-02

I649G1240044-02

1

I944H1240041-01

Содержание SFV650






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SFV650

Dakota Digital VHX systems Operating Manual preview
VHX systems
Бренд: Dakota Digital Страницы: 6
Yoshimura 14720BP520 Manual preview
14720BP520
Бренд: Yoshimura Страницы: 7
GAS GAS TXT PRO - PART LIST 2010 Parts List preview
TXT PRO - PART LIST 2010
Бренд: GAS GAS Страницы: 64
R&G CP0485 Fitting Instructions Manual preview
CP0485
Бренд: R&G Страницы: 47
Zero DSR 2018 Owner'S Manual preview
DSR 2018
Бренд: Zero Страницы: 162
Kabuto LEFF Instruction Manual preview
LEFF
Бренд: Kabuto Страницы: 20
GAS GAS 2003 FSE Parts List preview
2003 FSE
Бренд: GAS GAS Страницы: 26
DYNATEK DDK1-7 Installation Manual preview
DDK1-7
Бренд: DYNATEK Страницы: 12
Bosch DISBLAY DDU 7 Manual preview
DISBLAY DDU 7
Бренд: Bosch Страницы: 160
MSA Gallet F1 XF Operating Manual preview
Gallet F1 XF
Бренд: MSA Страницы: 168
GÜDE 16922 Translation Of The Original Instructions preview
16922
Бренд: GÜDE Страницы: 80
GÜDE 16926 Translation Of The Original Instructions preview
16926
Бренд: GÜDE Страницы: 88
Bajaj Dominar 400 Service Manual preview
Dominar 400
Бренд: Bajaj Страницы: 179
HYOSUNG RX 125 - Service Manual preview
RX 125 -
Бренд: HYOSUNG Страницы: 175
Yamaha YZF-R6 2000 Service Manual preview
YZF-R6 2000
Бренд: Yamaha Страницы: 32
Yamaha YZF250 Owner'S Manual preview
YZF250
Бренд: Yamaha Страницы: 98
Yamaha YZF-R6D Owner'S Manual preview
YZF-R6D
Бренд: Yamaha Страницы: 114
Yamaha YZF-R6P Owner'S Manual preview
YZF-R6P
Бренд: Yamaha Страницы: 128

Бренды по названию

Популярные бренды

Загрузить еще бренды