Suzuki SFV650 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 573

background image

Maintenance and Lubrication: 0B-11

6) Turn off the engine and wait about three minutes,

then check the oil level through the inspection
window (3). If the oil level is below the “L” mark, add
oil to the “F” mark. If the level is above the “F” mark,
drain the oil until the level reaches the “F” mark.

Oil Level Inspection

1) Keep the motorcycle upright.
2) Start up the engine and allow it to run for few minutes

at idle speed.

3) Turn off the engine and wait about three minutes,

then check the oil level through the inspection
window (1). If the level is below mark “L”, add oil to
“F” mark. If the level is above mark “F”, drain oil to
“F” mark.

Oil Filter Replacement

1) Drain engine oil as described in the engine oil

replacement procedure.

2) Remove the oil filter (1) using the special tool.

Special tool

(A): 09915–40620 (Oil filter wrench)

3) Apply engine oil lightly to the O-ring of new oil filter,

before installation.

CAUTION

!

ONLY USE A GENUINE SUZUKI
MOTORCYCLE OIL FILTER.
Other manufacturer’s oil filters may differ in
thread specifications (thread diameter and
pitch), filtering performance and durability
which may lead to engine damage or oil
leaks. Also, do not use a genuine Suzuki
automobile oil filter on this motorcycle.

4) Install a new oil filter. Turn it by hand until you feel

that the oil filter O-ring contacts the oil filter mounting
surface. Then, tighten the oil filter two full turns (or to
specified torque) using the special tool.

NOTE
To properly tighten the oil filter, use the
special tool. Never tighten the oil filter by
hand only.

Special tool

(A): 09915–40620 (Oil filter wrench)

Tightening torque
Oil filter (a): 20 N·m (2.0 kgf-m, 14.5 lbf-ft)

5) Add new engine oil and check the oil level is as

described in the engine oil replacement procedure.

Necessary amount of engine oil
Oil change: 2 400 ml (2.5/2.1 US/lmp qt)
Oil and filter change: 2 750 ml (2.9/2.4 US/lmp qt)
Engine overhaul: 3 000 ml (3.2/2.6 US/lmp qt)

3

I944H1020025-01

1

I944H1020026-01

1

(A)

I944H1020027-01

(A)

(a)

1

I718H1020026-01

«
...
35
36
37
38
39
...
»

Содержание SFV650






























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SFV650

Бренд: AJP Страницы: 191

Бренд: Yamaha Страницы: 287

COMFORT 10130810

Бренд: Contracor Страницы: 36

Бренд: GAS GAS Страницы: 74

Super Adventure 2016

Бренд: KTM Страницы: 25

Бренд: Termignoni Страницы: 9

Бренд: Paaschburg & Wunderlich Страницы: 2

Бренд: Suzuki Страницы: 42

Бренд: TVS Страницы: 60

Бренд: Baja motorsports Страницы: 66

Бренд: Eastwood Страницы: 8

Бренд: SUOMY Страницы: 26

Бренд: hepco & becker Страницы: 2

Бренд: Yamasaki Страницы: 28

Бренд: IBEX Страницы: 3

Бренд: Wunderkind Custom Страницы: 4

Бренд: SILENCE Страницы: 68

Бренд: APRILIA Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды