Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 102

Страница: 102 / 144

6-18

FatTwin F627R2-F73 USER'S MANUAL

6-11 Replacing System Fans

System fans provide cooling for the system and circulate air through the node as

a means of lowering the internal temperature. The F424BD system fans are easily

removed from the fan tray. There is no need to uninstall any other parts when

replacing fans, and only a Phillips screwdriver is required for installation.

Removing a Rear Exhaust Fan

1. Determine which motherboard node contains the failed fan and power down

the node with the operating system.

2. Power down the system and remove the power cord from the rear of the

power supply as described in Section 6-3.

3. Press the release tab on the bottom of the fan and pull it away from rear of

the node.

Installing a Rear Exhaust Fan

1. Press the release tab on the bottom of the fan and insert it into the open fan

bay.

2. Push the fan into the bay until it clicks into the locked position.

Figure 6-14: Replacing a Rear Exhaust Fans

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды