Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 110

Страница: 110 / 144

7-6

FatTwin F627R2-F73 FatTwin

system power to be turned on after a power loss. Select Last State to allow the

system to resume its last state before a power loss. The options are Power On,

Stay Off,

and

Last State



CPU Confi guration

This submenu displays the information of the CPU as detected by the BIOS. It also

allows the user to confi gure CPU settings.



Socket 1 CPU Information, Socket 2 CPU Information

This submenu displays the following information regarding the CPUs installed

in Socket 1 and Socket 2.

•

Type of CPU

•

CPU Signature

•

Microcode Patch

•

CPU Stepping

•

Maximum CPU Speed

•

Minimum CPU Speed

•

Processor Cores

•

Intel HT (Hyper-Threading) Technology

•

Intel VT-x Technology

•

Intel SMX Technology

•

L1 Data Cache

•

L1 Code Cache

•

L2 Cache

•

L3 Cache

CPU Speed

This item displays the speed of the CPU installed in the Socket selected.

64-bit

This item indicates if 64-bit technology is supported by the CPU installed in the
Socket selected.

Clock Spread Spectrum

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды