Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 57

Страница: 57 / 144

Chapter 5: Advanced Motherboard Setup

5-3

Installing the LGA2011 Processor

1. There are two load levers on the LGA2011 socket. To open the socket cover,

fi rst press and release the load lever labeled 'Open 1st'.

OPEN 1st

OPEN

1st

WARNING!

WAR

NIN

Press down on Load Lever
labeled 'Open 1st'.

OPEN 1st

OPEN

1st

WARNING!

WAR

NIN

5-4 Processor and Heatsink Installation

Caution!

When handling the processor package, avoid placing direct pressure on the

label area.

Note:

Always connect the power cord last, and always remove it before adding,

removing or changing any hardware components. Make sure that you install the

processor into the CPU socket before you install the CPU heatsink.

Caution!

If you buy a CPU separately, make sure that you use an Intel-certifi ed multi-

directional heatsink only.

Note:

Make sure to install the system board into the chassis before you install the

CPU heatsink.

Note:

When receiving a server board without a processor pre-installed, make sure that

the plastic CPU socket cap is in place and none of the socket pins are bent; otherwise,

contact your retailer immediately.

Note:

Refer to the Supermicro website for updates on CPU support.

Note:

When one CPU is installed, be sure to installed on CPU Socket 1 fi rst.

Note:

Graphics and drawings shown in this manual are for illustration only. Your

components may or may not look the same as the graphics shown in the manual.

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды