Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 56

Страница: 56 / 144

5-2

FatTwin F627R2-F73 USER'S MANUAL

5-3 I/O

Ports

The rear I/O ports are color coded in conformance with the PC 99 specifi cation. See

Figure 5-1 below for the colors and locations of the various I/O ports.

Back Panel I/O Port Locations and Defi nitions

Front Panel USB Port 1

Front Panel USB Port 2

Gigabit LAN 1

Gigabit LAN 2

IPMI LAN

VGA Port

Power Switch/LED Indicator

5-2 Connecting

Cables

Now that the processors are installed, the next step is to connect the cables to

the serverboard.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully

routed in preconfi gured systems to prevent them from blocking the fl ow of cooling air

that moves through the system from front to back. If you need to disconnect any of

these cables, you should take care to reroute them as they were originally connected

(make sure the red wires connect to the pin 1 locations). If you are confi guring the

system, keep the airfl ow in mind when routing the cables.

The following cables need to be connected for the FatTwin F627R2-F73 system:

•

Four (4) 23-cm w/25.5-cm SB 30AWG Ipass to 4 SATA cables (CBL-

0118L-03)

•

Four (4) 27-cm 8-pin to 8-pin ribbon SGPIO cable with tube (CBL-0157L-02)

•

Sixteen (16) 21-cm 30AWG SATA cables (CBL-0473L)

Figure 5-1. Rear I/O Ports

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды