Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 11

Страница: 11 / 144

Chapter 1

Introduction

1-1 Overview

The FatTwin F627R2-F73 is a high-end server comprised of two main subsystems:

the F424BD-R1K28B 4U server chassis and the X9DRFF-7 dual processor

serverboard in four hot-swap nodes. Please refer to our web site for information

on operating systems that have been certifi ed for use with the system (www.

supermicro.com).

In addition to the serverboard and chassis, various hardware components have

been included with the FatTwin F627R2-F73 server, as listed below:

•

Eight (8) 2U passive CPU heatsinks for CPU (SNK-P0048P)

•

Power cables:

Four (4) 15-cm 2x2 to 2x2 18AWG power cables (CBL-0486L)

Four (4) 30-cm 2x2 to 2x2 18AWG power cables (CBL-PWEX-0486L-01)

•

SAS/SATA Backplane

Four (4) backplanes for thirty-two (32) 2.5" HDD (BPN-SAS-F424-B8)

Thirty-Two (32) hot-swap 2.5" HDD trays (MCP-220-00098-0B)

Four (4) 23-cm w/25.5-cm SB 30AWG Ipass to 4 SATA cables

(CBL-0118L-03)

Four (4) 27-cm 8-pin to 8-pin ribbon SGPIO cable with tube (CBL-0157L-02)

Sixteen (16) 21-cm 30AWG SATA cables (CBL-0473L)

•

Four (4) Riser cards (RSC-R1UFF-E16R-O-P)

•

One (1) F418/F424 Rail set (MCP-290-41803-0N)

Note:

For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

•

Supermicro product manuals:

http://www.supermicro.com/support/manuals/

•

Product drivers and utilities:

ftp://ftp.supermicro.com

•

Product safety information:

http://super-dev/about/policies/safety_information.cfm

•

If you have any questions, please contact our support team at:

[email protected]

Chapter 1: Introduction

1-1

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды