Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 121

Страница: 121 / 144

Chapter 7: BIOS

7-17

SERR# Generation

Select Enabled to allow a PCI device to generate an SERR number for a PCI Bus

Signal Error Event. The options are Enabled and

Disabled

Maximum Payload

Select Auto to allow the system BIOS to automatically set the maximum payload

value for a PCI-E device to enhance system performance. The options are

Auto

128 Bytes and 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.

Maximum Read Request

Select Auto to allow the system BIOS to automatically set the maximum Read

Request size for a PCI-E device to enhance system performance. The options are

Auto

, 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.

ASPM Support

This feature allows the user to set the Active State Power Management (ASPM)

level for a PCI-E device. Select Auto to allow the system BIOS to automatically

set the ASPM level for the system. Select Disabled to disable ASPM support. The

options are

Disabled

, and Auto.

Warning

: Enabling ASPM support may cause some PCI-E devices to fail!

Above 4G Decoding (Available if the system supports 64-bit PCI decoding)

Select Enabled to decode a PCI device that supports 64-bit in the space above 4G

Address. The options are Enabled and

Disabled

CPU1 Slot 1 PCI-E 3.0 x16 OPROM

Select Enabled to enable Option ROM support to boot the computer using a device

installed on the slot specifi ed above. The options are

Enabled

and Disabled.

CPU2 Slot 2 PCI-E 3.0 x16 OPROM

Select Enabled to enable Option ROM support to boot the computer using a device

installed on the slot specifi ed above. The options are

Enabled

and Disabled.

Onboard LAN Option ROM Select

Select iSCSI to use the iSCSI Option ROM to boot the computer using a network

device. Select PXE (Preboot Execution Environment) to use an PXE Option ROM

to boot the computer using a network device. The options are iSCSI and

PXE

Load Onboard LAN1 Option ROM, Load Onboard LAN2 Option ROM

Select Enabled to enable the onboard LAN1/LAN2 Option ROM. This is to boot

the computer using a network device. The default setting for LAN1 Option ROM is

Enabled

, and the default setting for LAN2 Option ROM is

Disabled

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды