Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 16

Страница: 16 / 144

1-6

FatTwin F627R2-F73 USER'S MANUAL

Mounting Rails

The F424BD includes a set of rails, and can be placed in a rack for secure storage

and use. To setup your rack, follow the step-by-step instructions included in this

manual.

1-4 Advanced Power Management

Intel® Intelligent Power Node Manager (NM)

The Intel® Intelligent Power Node Manager (IPNM) provides your system with

real-time thermal control and power management for maximum energy effi ciency.

Although IPNM Specifi cation Version 1.5 is supported by the BMC (Baseboard

Management Controller), your system must also have IPNM-compatible

Manageability Engine (ME) fi rmware installed to use this feature.

Manageability Engine (ME)

The Manageability Engine, which is an ARC controller embedded in the IOH (I/O

Hub), provides Server Platform Services (SPS) to your system. The services

provided by SPS are different from those proveded by the ME on client platforms.

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды