Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 71

Страница: 71 / 144

Chapter 5: Advanced Motherboard Setup

5-17

Universal Serial Bus (USB)

Two Universal Serial Bus ports (USB1,

USB2) are located at (JUSB1, JUSB2)

the I/O back panel. (USB Cables are not

included). See the table on the right for

pin defi nitions.

Backplane USB 0/1

& FP USB 2

Pin Defi nitions

Pin# Defi nition

+5V

PO-

PO+

Ground

Video Connector

A Video (VGA) port is located next to

JUSB1 on the I/O backplane. Refer to

the board layout below for the location.

Ethernet LAN Ports

Two Gigabit Ethernet ports (LAN1,

LAN2) are located on the I/O backplane

on the motherboard. In addition, an IPMI

LAN is also on the backplane. All these

ports accept RJ45 type cables. Please

refer to the LED Indicator Section for

LAN LED information.

LAN Ports (LAN1/2)

Pin Defi nition

Pin# Defi nition Pin# Defi nition

P2V5SB

SGND

TD0+

Act LED

TD0-

P3V3SB

TD1+

Link 100 LED
(Yellow, +3V3SB)

TD1-

Link 1000 LED
(Yellow, +3V3SB)

TD2+

Ground

TD2-

Ground

TD3+

Ground

TD3-

Ground

Serial Ports

A COM connection (COM1) is located

next to the Front Control Panel (JF1) on

the motherboard. See the table on the

right for pin defi nitions.

Serial Port Pin Defi nitions

(COM1)

Pin # Defi nition

DCD

DSR

RXD

RTS

TXD

CTS

DTR

Ground

NC indicates no connection.

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды