Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 128

Страница: 128 / 144

7-24

FatTwin F627R2-F73 FatTwin

This item displays the status of TPM Support to indicate if TPM is currently

active or deactivated.

TPM Owner Status

This item displays the status of TPM Ownership.



Intel TXT (LT-SX) Confi guration

Intel TXT (LT-SX) Hardware Support

This feature indicates if the following hardware components support the Intel

Trusted Execution Technology.

CPU

TXT (Trusted Execution Technology) Feature

Chipset

TXT (Trusted Execution Technology) Feature

Intel TXT (LT-SX) Confi guration

This feature displays the following TXT confi guration setting.

TXT (LT-SX) Support

This item indicates if the Intel TXT support is enabled or disabled. The default

setting is

Disabled

Note

: Be sure to format your TPM module before enabling TXT (LT-SX)

support for this feature to work properly.

Intel TXT (LT-SX) Dependencies

For Trusted Execution Technology to work properly in the system, be sure to

enable the features displayed below.

VT-d Support

Intel Virtualization Technology with Direct I/O support

VT Support

Intel Virtualization Technology support

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды