Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 105

Страница: 105 / 144

Chapter 7: BIOS

7-1

Chapter 7

BIOS

7-1 Introduction

This chapter describes the AMI BIOS Setup Utility for the X9DRFF-7 serverboard.

The 128 Mb AMI BIOS® is stored in a Flash EEPROM and can be easily updated.

This chapter describes the basic navigation of the AMI BIOS Setup Utility setup

screens.

Starting BIOS Setup Utility

To enter the AMI BIOS Setup utility screens, press the <Del> key while the system

is booting up.

Note

: In most cases, the <Del> key is used to invoke the AMI BIOS setup screen.

There are a few cases when other keys are used, such as <F3>, <F4>, etc.

Each main BIOS menu option is described in this manual. The Main BIOS setup

menu screen has two main frames. The left frame displays all the options that can

be confi gured. Grayed-out options cannot be confi gured. Options in blue can be

confi gured by the user. The right frame displays the key legend. Above the key

legend is an area reserved for informational text related to the option currently

selected in the left frame.

Note

: The AMI BIOS has default informational messages built in. The manufacturer

retains the option to include, omit, or change any of these informational messages.

The AMI BIOS Setup utility uses a key-based navigation system called "hot keys."

Most of the AMI BIOS setup utility "hot keys" can be used at any time during setup

navigation. These keys include <F3>, <F4>, <Enter>, <ESC>, arrow keys, etc.

Note 1

: In this section, options printed in

Bold

are default settings.

Note 2

: <F3> is used to load optimal default settings. <F4> is used to save the

settings and exit the setup utility.

How To Change the Confi guration Data

The confi guration data that determines the system parameters may be changed by

entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing

<Delete> at the appropriate time during system boot.

Note

: For AMI UEFI BIOS Recovery, please refer to the UEFI BIOS Recovery User

Guide posted @

http://www.supermicro.com/support/manuals/

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды