Supero FatTwin F627R2-F73 Скачать руководство пользователя страница 130

Страница: 130 / 144

7-26

FatTwin F627R2-F73 FatTwin

Enabling/Disabling Options

SMBIOS Event Log

Select Enabled to enable SMBIOS (System Management BIOS) Event Logging

during system boot. The options are

Enabled

and Disabled.

Runtime Error Logging Support

Select Enabled to support Runtime Error Logging. The options are

Enabled

and

Disabled.

Memory Correctable Error Threshold

This feature allows the user to enter the threshold value for correctable memory

errors. The default setting is

PCI Error Logging Support

Select Enabled to support error event logging for PCI slots. The options are Enabled

and

Disabled

Erasing Settings

Erase Event Log

Select Enabled to erase the SMBIOS (System Management BIOS) Event Log, which

is completed before an event logging is initialized upon system reboot. The options

are

, Yes, next reset, and Yes, every reset.

When Log is Full

Select Erase Immediately to immediately erase SMBIOS error event logs that

exceed the limit when the SMBIOS event log is full. Select Do Nothing for the system

to do nothing when the SMBIOS event log is full. The options are

Do Nothing

and

Erase Immediately.

SMBIOS Event Log Standard Settings

Log System Boot Event

Select Enabled to log system boot events. The options are

Disabled

and Enabled.

Содержание FatTwin F627R2-F73

















































































































































Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды

Supero FatTwin F627R2-F73, Руководство пользователя

Результаты поиска

Содержание FatTwin F627R2-F73

Отзывы:

Похожие инструкции для FatTwin F627R2-F73

Бренды по названию

Популярные бренды