manualshive.com logo in svg

Star Headlight & Lantern LCS850MG, Инструкция по установке и эксплуатации

Поделиться
Скачать
Star Headlight & Lantern LCS850MG Скачать руководство пользователя страница 54

-47- 

Operation 

Audio Mode Buttons 

Volume Controls 

The five (5) push buttons across the middle of the 
control head are used to select the various “audio 
modes”.  When these buttons are NOT activated, 
they are backlit in green for nighttime viewing.  
When activated, an audible beep is heard, and the 
backlighting turns red. 

 

  Hands Free (HF): 

Also known as Horn Ring Cycler, allows the user to cycle through Wail, 
Yelp, Phaser, and Standby (Off) by repeatedly pressing the horn or other 
switch connected to the AUX input.  Operating any other mode resumes 
normal operation.  

Please note: this mode disables the Manual (MAN) 

push button selection when a Wail, Yelp, or Phaser tone is cycled to.

 

 

 

WAIL: 

A normal rise-fall tone generally used on highways and areas with low 
traffic or constant traffic flow. 

 

 

YELP: 

A rapid warble tone used in light to moderately congested areas. 

 

  Phaser (PHSR): 

Ultra-fast warble tone used for maximum attention in highly congested 
areas. 

 

 

RADIO: 

Also known as Radio Repeat, this function amplifies the two-way radio 
through the siren speaker(s).  PA is available, but no siren tones are 
available in this position. 

 

PA Volume Control 

Radio Volume Control 

Audio Mode Buttons 

The 

PA volume control

 (PA) will control the public address volume.  It is located in the lower 

left hand corner of the front face.  Insert a small, flat blade screwdriver into the PA  
volume adjustment port.  Turn counter-clockwise direction to 
increase the sound level.  Typically it will not need to be 
changed once it has been set. 

 

(This adjustment does not affect the radio rebroadcast 
volume.  The radio repeat volume  control is located inside 
the amp unit.  For details see above.) 

The 

Radio Repeat volume control

 will control the rebroadcast volume.  It is located inside the 

amplifier case.  Typically it will not need to be changed once it has been set. 

 

Locate the 

Radio Repeat volume control

 inside the housing towards the right hand side and 

use a small Phillips head screwdriver to adjust the volume.

 

Содержание LCS850MG

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды