Star Headlight & Lantern LCS850MG, Инструкция по установке и эксплуатации

Страница: 50 / 64

-43-
Installation: Wiring
12-Terminal Connector (Audio I/O)
(See wiring diagram on page 44)
Terminal 1: Speaker 2 (Negative) -
<BROWN>
Connect to the negative terminal from your
second speaker. Use a minimum 14 AWG wire.
Terminal 2: Speaker 2 (Positive) -
<BROWN w/WHITE>
Connect to the positive terminal from your second
speaker. Use a minimum 14 AWG wire.
Terminal 3: Park/Kill -
<GRAY>
Used for the Park/Kill feature that automatically deactivates the siren (such as when the vehicle is
placed in Park or a door is opened). Using an 18 AWG wire, connect this terminal to the dome light,
a door switch, or other external switch. By default this wire activates the Park/Kill feature when it
re12VDC. Optionally, this input can be set to activate the Park/Kill feature when it is
grounded (see page 9 of the Installer Selectable Options).
Terminal 4: Remote Enable -
<YELLOW>
Use an 18 AWG wire to connect this terminal to +12VDC through a switched power supply (possibly
ignition). This will turn the siren and light controls off when the ignition is off. Be sure to use
minimum size #18 AWG wire.
NOTE: It is NOT recommended that you connect this to constant
+12VDC. This wire must have +12VDC applied to it for the lights and siren to work.
Terminal 5 & 6: Radio 1 & Radio 2 -
<BLUE>
Used for radio repeat. Connect one terminal to one output and the other terminal to the other output
from the two-way radio (speaker or output connector). This unit has been designed such that polarity
is not important. Use #18 AWG wire.
Terminal 7: Auxiliary (Horn Ring Transfer In) -
<GREEN>
Used for remote Manual (or Air Horn) control. Using an 18 AWG wire, connect to the horn ring circuit
or some other remote switch. Typically the Horn wire is disconnected from the Horn and connected
to this wire. By default this wire activates the Auxiliary feature when it re12VDC. Optionally,
this input can be set to activate the AUX feature when it is grounded (see page 9 of the Installer
Selectable Options).
Terminal 8: Horn Ring Transfer Out -
<GREEN w/YELLOW>
If you are using the Auxiliary wire listed above, connect this terminal to the side of your vehicle horn
that was disconnected when the horn ring circuit was connected to the AUX wire (see
Auxiliary
above). This allows for normal functioning of your vehicle horn when the siren is off. Normal
installation of this unit has the vehicle’s horn switch disconnected from the horn and routed to the
Auxiliary terminal (see the Wiring Diagram on page 44). Use 18 AWG wire.
Terminal 9: Gun Lock (Optional Backlight Dim) -
<GREEN w/WHITE>
By default, this input is designed to enable the Gun Lock button when +12VDC is applied to it. If you
desire, it can instead be used to dim the backlighting when +12VDC is applied to it (
see page 33 of the
Optional Settings section).
Terminal 10: Speaker 1 (Negative) -
<BROWN>
Connect to the negative terminal from your first speaker. Use a minimum 14 AWG wire.
Terminal 11: Speaker 1 (Positive) -
<BROWN w/WHITE>
Connect to the positive terminal from your first speaker. Use a minimum 14 AWG wire.
Terminal 12: Backlight Dim (Optional Gun Lock) -
<ORANGE>
By default, this input is designed to dim the backlighting for night driving when Ground is applied to it.
If you desire, it can instead be used to release the Gun Lock when Ground is applied to it (
see page 33
of the Optional Settings section).
P30041-68
12-Terminal Audio Connector Inputs and Outputs