6
EnglisH
7
EnglisH
n
use
charging the battery using
the battery clamps
WARning:
Always disconnect the AC plug from the AC mains socket first before connecting or disconnecting the
charger to or from the battery to be charged. Always follow the steps outlined in the “Safety Instructions” section at the
front of this manual.
1. Connect the battery clamps to the battery charger with the double-barrel in-line connector. The battery clamps are
color-coded. Red is positive; black is negative. These clamp directly to the corresponding connectors on the battery
terminals.
2. Insert the AC plug of the battery charger into an AC mains socket. The Power LED will light green to indicate the
unit is in standby mode and ready to use.
notes:
If the Power LED did not come on, check connection with the AC mains socket. Make sure the AC mains socket is functional.
3. When the charger is properly connected, choose the following operation mode for the battery to be charged by
pressing the Mode Selector Button.
•
Motorcycle Mode, suitable for most of small vehicle like motorcycle
•
Vehicle Mode, aims for general automotive vehicle.
•
Frozen Mode, best for cold weather condition.
The corresponding mode of LED will light (green for Motorcycle Mode and Vehicle Mode, orange for Frozen Mode).
The charging process will start automatically for few seconds and the Charging LED will light orange to indicate the
unit is in charging mode.
notes:
If the battery clamps are connected incorrectly with regard to polarity, the Reverse Polarity LED will light red. Disconnect the
charger’s AC plug from the AC mains socket; then disconnect the clamps. Reconnect the clamps with correct polarity and plug
the charger back in at the AC mains socket. Then select the correct operation mode.
If the Charging LED did not come on, check the connection to the battery. If the clamps are properly connected, the battery
may be in fault condition. Manufacturer suggests to have the battery tested by a qualified battery service technician.
4. When the battery is completely charged, the charger will automatically goes into Float Charge Mode and the
Charged LED will light green. In this mode, the charger monitors the battery voltage and charges as necessary to
assure the battery maintains full capacity.
The charger remains in Float Charge Mode as long as the charger is connected to the battery and is plugged into
a functioning AC mains socket.
When disconnecting the charger, do so in the following order: Disconnect the AC mains plug from the AC mains socket,
then disconnect the battery clamps from the battery terminal.
charging the battery using the vehicle adaptor plug
WARning: nEVER connect this unit to a positive grounded vehicle by the vehicle Adapter Plug.
Always follow
the steps outlined in the “Safety Instructions” section at the front of this manual.
1. Connect the vehicle adaptor plug to the battery charger with the double-barrel in-line connector. Insert the plug into
the 12 V DC accessory outlet of the vehicle.
2. Insert the AC plug of the battery charger into an AC mains socket. The Power LED will light green to indicate the
unit is in standby mode and ready to use.
notes:
If the Power LED did not come on, check connection with the AC mains socket. Make sure the AC mains socket is functional
3. When the charger is properly connected, choose the following operation mode for the battery to be charged by
pressing the Mode Selector Button.
•
Motorcycle Mode, suitable for most of small vehicle like motorcycle
•
Vehicle Mode, aims for general automotive vehicle.
•
Frozen Mode, best for cold weather condition.
The corresponding mode of LED will light (green for Motorcycle Mode and Vehicle Mode, orange for Frozen Mode).
The charging process will start automatically for few seconds and the Charging LED will light orange to indicate the
unit is in charging mode.
note:
Some vehicles require that the ignition be switched to the accessory outlet position in order to power the accessory outlet.
If the charging LED did not come on, check the connection to the 12 V DC accessory outlet of the vehicle. Rotate the plug
slightly to make sure there is good contact. If the connection is properly checked, the battery may be in fault condition.
Manufacturer suggests to have the battery tested by a qualified battery service technician.
4. When the battery is completely charged, the charger will automatically goes into Float Charge Mode and the
Charged LED will light green. In this mode, the charger monitors the battery voltage and charges as necessary to
assure the battery maintains full capacity.
The charger remains in float charge mode as long as the vehicle adaptor plug is inserted to the 12 V DC accessory
outlet of the vehicle and is plugged into a functioning AC mains socket.
Follow the manufacturers’ instructions to remove any insulating covers from the battery posts. Connect the positive
(red) clamp from the battery charger to the positive (POS, P, +) post of the battery.
Connect the negative (black) clamp from the battery charger to the negative (NEG, N, –) post of the battery or to the
chassis. Then, connect the AC plug of the battery charger into the AC mains socket.
When disconnecting the battery charger from the battery, always:
•
Switch off and unplug the battery charger.
•
Remove the negative (black) clamp first
•
Remove the positive (red) clamp or last.
•
Refit any insulating covers to the battery posts.
chargIng a battery dIsconnected froM the cIrcuIt
WARning:
Incorrect connection, battery short circuit, location of battery and location of the battery charger may
create a hazard. Make sure that adequate preparation has been made before proceeding.
If the battery is not already removed from the circuit, follow the manufacturers’ instructions to remove the battery before
charging.
Check the polarity of the battery posts. A positive (POS,P, +) battery post usually has a larger diameter than the
negative (NEG, N, –) battery post.
Connect the positive (red) clamp from the battery charger to the positive (POS, P, +) post of the battery. Connect the
negative (black) clamp from the battery charger to the negative (NEG, N, –) post of the battery. Then, connect the AC
plug of the battery charger into the AC mains socket.
When disconnecting the battery charger from the battery, always:
•
Switch off and unplug the battery charger.
•
Remove the negative (black) clamp first.
•
Remove the positive (red) clamp or last.
•
Refit any insulating covers to the battery posts.
guIde to controls and IndIcators
charging lED:
Lights orange to indicate there is a good connection to the battery and the battery is
charging.
charged lED:
Lights green to indicate the battery is fully charged. The unit automatically goes into
Float Charge mode.
Reverse polarity lED:
Lights red to indicate a reverse polarity connection is detected.
Mode selector Button:
Button for selecting Motorcycle Mode, Vehicle Mode or Frozen Mode
Power lED:
Lights green to indicate the unit is properly plugged into a functional AC mains socket.
Motorcycle Mode lED:
Lights green when this mode is selected (suitable for most small vehicles,
such as motorcycles).
Vehicle Mode lED:
Lights green when this mode is selected (suitable for general automotive
vehicles).
Frozen Mode lED:
Lights orange when this mode is selected (for use in cold weather conditions).
BC8EU_Manual_040512.indd 6-7
4/5/2012 6:02:24 PM
