1. Overview
9
Location and Function of Parts
Operator Side
Air inlet
5
3
8 7
9
10
11
12
13
15
16
14
1 2
4
6
Air inlet
AXS memory card slot
[Note]
Do not operate with the air inlet blocked.
1.
ASSIGN (assignable) buttons 1/2
(page 48)
Assign functions using the EDIT page of the
user functions screen (page 48).
The assigned function toggles between on/off
(enabled/disabled) or is activated with each
press.
2.
ASSIGN (assignable) lamps 1/2
(page 48)
The lamp is lit orange when the assigned
function is on (enabled) or activated, and not
lit when the function is off (disabled).
3.
Built-in speaker
You can monitor the input audio during
shooting/recording and playback sound
during playback. The speaker also sounds
alarms to reinforce visual warnings
(page 95).
If you connect earphones to the headphones
jack, the speaker output is suppressed
automatically.
[Note]
If configured such that the internal microphone captured
sound is audible from the built-in speaker, howling may
occur if the monitor volume is increased.
4.
Mini display ITEM keys 1 to 3
Controls the operation of functions on the
mini display (page 96).
5.
Mini display
Displays various setup items, such as
shutter angle, that you can check or modify
(page 96).
6.
ACCESS lamps (SLOT A/B)
Each lamp is lit when the recording media in
AXS card slot A/B is the target for recording/
playback and when data is being written to or
read from the recording media in AXS card slot
A/B (page 26).
7.
CLIPS button
Press to display the clip screen on the mini
display to enable clip operations (page 99).
Simultaneously, the clip list screen is displayed
on the sub display and can also be used for
clip operations.
To switch from playback mode to shooting
mode, press the HOME button.
8.
SLOT SELECT (AXS memory card select)
button
Press to switch the active slot.
9.
Power switch
Set to the
(ON) position to turn the power on.
Set to the
(OFF) position to turn the power
off.
[Notes]
• This unit uses a small amount of standby power
even when the power switch is set to OFF. Remove
the battery pack if the unit will not be used for a
prolonged period.
• When removing the battery pack or the DC IN
power, be sure to first set the power switch to the
OFF position. Interrupting the power supply during
recording or during memory card access could cause
a malfunction.
10.
HOME button
Press to clear the item selection display and
return to the Home screen on the mini display.
If pressed when the unit is in playback
state, the unit transitions to shooting mode
(page 96).
11.
LOCK switch
Locks the operation of the buttons on the
Operator side. When locked, the switch
background LED lights in orange.
12.
Headphones connector (stereo mini jack)
Connect to earphones for audio monitoring.
You can monitor the input audio during
shooting/recording and playback sound
during playback (page 95).
[Notes]
• Use monaural (2-pole) or stereo (3-pole) type
earphones. The use of other devices may damage
the unit.
• Use 16-ohm impedance earphones.
13.
REC ACTIVE lamp
The lamp is lit green when the REC button is
enabled.
14.
ASSIGN (assignable) lamp 3 (page 48)
The lamp is lit orange when the assigned
function is on (enabled) or activated, and not
lit when the function is off (disabled).
15.
REC (recording start/stop) button/lamp
Press to start recording, turning the REC lamp
on. Press again to stop recording, turning the
REC lamp off (page 107).
The REC lamp flashes when a device error or
warning occurs.
16.
Ф (phi) mark
The Ф (phi) mark is on the same plane as the
image sensor.
To measure the precise distance between the
unit and the subject, use the Ф (phi) mark as a
reference.