solexx Garden Master G-512 страница 29 Скачать руководство пользователя | Manualshive

Страница: 29 / 29

background image

12’ Garden Master (3.5mm) Page 29

1. Standing inside the greenhouse, push the

Louver

through the hole on the back end wall. Attach with 1” Screws through the

rim of the louver and into the 12 ½” pipes.

2. If you are using the manual opener, attach the dial on the bottom frame of the Louver. Attach the chain to the top of the

lever and also to the bottom hole in the center bar on the Louver. To adjust the louver simply push the lever down to open
the louver and tighten the wing nuts.

Notes:

15. LOUVER

Pieces Required:

1 Louver
1

Bag of parts.

4 1” Screws

Louver

1” Screw

12 ½” Pipe

Other Helpful Hints

1. Caulk any holes from screws or punctures in the panels to help keep bugs and dirt out.
2. Be sure your Greenhouse is properly anchored to the ground or a foundation.

DURING AND AFTER ASSEMBLY

3. Remove Shade Cloth in the winter.
4. Please call us if you have questions about assemblying your greenhouse.
5. We welcome pictures of your greenhouse in use. Send to [email protected]

ENJOY YOUR NEW GREENHOUSE!

P.S. Please share with us any ideas you have on improving our kits. Pictures are appreciated.

Copyright Adapt8 11/92

FEB. 2020 4th Edition V-1 Edition

«
...
27
28
29

Содержание Garden Master G-512






























Отзывы:

Нет отзывов

Похожие инструкции для Garden Master G-512

Бренд: MACHRUS Страницы: 29

St. Helens GH370

Бренд: Electrovision Страницы: 2

SIGMA 2021 EURO

Бренд: PLANTA Страницы: 25

Victory Orangery - Garden Chalet

Бренд: Palram Страницы: 105

Бренд: ClearSpan Страницы: 21

Бренд: LAMS Страницы: 80

Бренд: R & M Int'l. Страницы: 10

Бренд: AeroGarden Страницы: 16

Бренд: AeroGarden Страницы: 26

Бренд: Outsunny Страницы: 7

Бренд: Outsunny Страницы: 17

Бренд: DrivhusSenter Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды