Page 10
12’ Garden Master (3.5mm)
1. Attach a
22” Composite Tube - White (Double-Slotted)
into the Snap-T’s on Both BS - 92” Base Frame tubes. Secure tubing into the
Snap-T’s with a 1” Screw. See diagram 1 above.
2. Attach
Middle End wall
to the 4-way Metal-T’s on the Middle Base Frame and tighten the eyebolts. (The Lower and middle 4-way
metal-T’s face towards the front base assembly. See diagram 2 above and diagram below.)
3. Insert the
BB - 92” Composite Tubes
into the bottom 4-way Metal-T’s on the 90” Composite Tubes - Yellow (Middle End wall). Attach
the end of the BB - 92” composite tubes that were marked BB from step 3A-5, into the post and tighten the eyebolts. There are 3
snap-T’s on the middle of the BB tubes, of these three snap-T’s, join the snap-T that is farthest from the Middle end wall onto the 22”
composite tube - white (Double-Slotted), from Step 6-1 above. Next, attach a
24” Composite Tube - Orange (Double-Slotted)
into
the Snap-T that is closest to the Middle end wall (on both BB - 92” Composite tubes). Secure all Snap-T’s to the tubes with 1” Screws.
See diagram 3 above and diagram below.
4. Insert the
TB - 92” Composite Tubes
into the Middle 4-way Metal-T’s on the 90” Composite Tubes - Yellow (Middle End wall). Attach
the end of the TB - 92” composite tubes that were marked TB from step 3A-5, into the post and tighten the eyebolts. Attach the 24”
composite Tubes - orange (Double-Slotted) to the Snap-T’s (That are right of center - Closest to the middle end wall) on both TB - 92”
Composite Tubes. Secure them with1” Screws. See diagram 4 above and diagram below.
5. Use a marker and draw a line 2 ¾” in from both ends of the
92” Composite Tubes - Red
(Do this on both tubes). Put 92” Composite
Tubes - red into the top 4-way metal-T’s on the Middle End Wall. Slide tubes into the posts until the line you just marked on them is even
with the post and tighten the eyebolts. See diagram 5 above and diagram below.
6. Lift and attach the
Front End wall
to the 4-way Metal-T’s on the Front Base Frame and tighten the eyebolts. Insert the opposite sides of
the 92” Composite Tubes (Including all TB and BB
assemblies) into the corresponding Metal Fittings and
tighten the eyebolts.
Check the measurements of the Hanging Rods.
They should be 92 ¾” from the “in” side of one 35 ¾”
Middle End Wall tube to the center of the 35 ¾” Front
End wall tube. See diagram 6 and diagram to the right.
7. Insert both
44” Composite Tubes - Red
into the 4-way
Metal-T’s at the top of the Middle End Wall. See
diagram 7 and diagram to the right.
8. Attach the
Back End Wall (Insert slotted end
completely
into the Snap-T’s on the Back base frame.
Use glue to help lubricate the tube to make it easier to
slide into the Snap-T’s. The glue does not adhere to
the Composite Tubing, so you will have to secure the
tubing by drilling a screw through the top of the
snap-T and into the 90” Composite Tubes.
Insert the opposite ends of the 44” Composite Tubes into
the Metal Corner Posts at the top of the Back End Wall.
The measurement from the “in” side of the 35 ¾” Middle
End wall tube to the center of the opposite 35 ¾” Back
End Wall tube should be 44 ¼”
6.
6. HANGING RODS & BENCH RODS
Pieces Required:
2 22” Composite Tube - White (
Double-Slotted
)
1 Middle End wall (
from Step 5B
)
2 BB - 92” Composite Tube - RED (
from step 3
)
2 24” Composite Tube - Orange (
Double-Slotted
)
2 TB - 92” Composite Tube - RED (
from step 3
)
2 92” Composite Tube - RED
1 Front End wall (
from Step 5A
)
2 44” Composite Tube - Red
1 Back End wall (
from Step 5C
)
8 1” Screws
1.
2.
3.
4.
5.
7.
8.
Two people & ladder recommended!
Hanging
Rod
Front
End Wall
44 ¼”
Middle
End wall
92” Composite
Tubing - Red
92 ¾”
Back
End wall
24”
Composite
Tubing
(Double
Slotted)
TB
92”
Composite
Tubing
22” Composite
Tubing
white (Double-slotted)
BB
92” Composite
Tubing
BS - 92” Base Frame Tube
44”
Com-
posite
tube
Red
