manualshive.com logo in svg

solexx Garden Master G-512, Руководство по сборке

Поделиться
Скачать
solexx Garden Master G-512 Скачать руководство пользователя страница 7

12’ Garden Master (3.5mm)                                                                     Page 7

4.  Attach the fittings of the Middle Base Frame assembly (made in step 3B-2) to the open ends of both BF - 92” Composite

Tubes - RED and both BS - 92” Composite Tubes - RED

.

Push both BS - 92” Composite Tubes - RED all the way into the 

4-way Metal-T’s. Adjust the middle base frame assembly so that the measurements from the “in” side edge of the Front
Base Assembly to the center of the Back Base Assembly is 92 ¾”.  

5.  Attach both 

44” Composite Tubes - Red (with Snap-T’s from Step 3B-3)

to the 4-way metal-T’s on the ends of the

Middle Base Frame.

6.  Attach the Metal Corner Posts of the Back Base Frame assembly to the opposite ends of the 44” Composite Tubes - Red

that you just added in the step above (Step 4-5). Making sure the arm with the red mark is facing up on the metal corner
posts. Adjust the Back Base Frame Assembly so that the measurement from the 94 ½” Composite Tube of the Middle Base 
Frame Assembly to the 94 ½” Composite Tube of the Back Base Frame Assembly is 44 ¼” from “in” side to center. Tighten
the eyebolts.

7.   Attach a 

94 ½” Composite Tube - Green (Double-Slotted)

into the Snap-T’s on the 44” Composite Tubes (added in Step

4-5) that are closest to the Back Base Frame Assembly. 

Use glue to help lubricate the tube to make it easier to slide

into the Snap-T’s. The glue does not adhere to the CompositeTubing, so you will have to secure the tubing by
drilling a screw through the top of the Snap-T and into the 94 ½” Composite Tube. 

Attach two 

Snap-T’s

on to the

94 ½” Composite Tube - Green.  Line up the Snap-T’s with the Snap-T’s that are on the Back Base Frame assembly.

CONT.....  BASE FRAME

44” Composite Tubing - Red

Snap-T

Snap-T

Back Base Frame

Middle Base Frame

44 1/4”

(“In” side to center)

Corner Post with red 
mark pointing up

BF

- 92” Composite Tubing

- 

Red 

Middle Base Assembly

FRONT

SIDE

SIDE

BF

- 92” Composite Tubing

- 

Red 

95 ¼” (“In” side to center)

BS

- 92” Composite

Tubing - Red 

92 ¾” (“In” side to center)

4-Way Metal-T

BS

- 92” Composite

Tubing - Red 

4-Way Metal-T

94 

½”

Composite Tube

Green (Double-Slotted)

Snap-T

Содержание Garden Master G-512






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды