background image

Chapter 10: Setting Up Communication to the 

Monitoring Portal

Power optimizers send information to the inverter via the DC power lines (the PV output circuit).  The 
information is sent from the inverter  to the SolarEdge monitoring portal through the Internet. In order 
to send the data from the inverter, a communication connection must be set up, as described in this 
chapter.

 

CAUTION!

When connecting the communication cables, make sure that the ON/OFF switch at the bottom 

of the inverter is turned OFF, and the AC is turned OFF.

When configuring the communication parameters, make sure that the ON/OFF switch is OFF, 

and the AC is turned ON. 

 

Lors de la connexion des câbles de communication, assurez-vous que l'interrupteur 
MARCHE/ARRÊT à la base de l'onduleur soit en position ARRÊT, et le CA est en position 
ARRÊT. Lors de la configuration des paramètres de communication, assurez-vous que 
l'interrupteur MARCHE/ARRÊT soit en position ARRÊT, et le CA est en position MARCHE.

Chapter 10: Setting Up Communication to the Monitoring Portal

SolarEdge

-

StorEdge Installation Guide MAN-01-00262-1.0

71

Содержание storedge
































































































Отзывы: