Wavetronix click 301 Скачать руководство пользователя страница 1

Страница: 1 / 13

1 of 13

WX-501-0531 • 01.22

Using the Click 301

The Click 301 serial to Ethernet converter changes half-duplex two-wire RS-232 and RS-485 communication to

Ethernet and vice versa. Use this device in a cabinet to transfer data from a sensor to your computer or traffic

operations center via a wired network connection.

Physical Features

The Click 301 has several communication ports, as well as features for configuration (see the figure below).

Mode

Switch

LED Indicators

RS-485

Connector

RS-232

Connector

Ethernet

Connector

T-Bus

Connector

TOP

FRONT

Communication Ports

The back of the Click 301 features a 5-position connector that plugs into a T-bus connector and provides power

and RS-485 communication to the device. It also passes RS-485 communication from the module to all other

devices on the T-bus.

The top of the device has a pluggable screw terminal block that features -485, one +485 and two ground screw

terminals for wiring RS-485 communication. This screw terminal block can be removed for easy preinstallation

0531

Содержание click 301














Результаты поиска

Содержание click 301

Отзывы:

Похожие инструкции для click 301

Бренды по названию

Популярные бренды

Wavetronix click 301, Инструкция по использованию

Результаты поиска

Содержание click 301

Отзывы:

Похожие инструкции для click 301

Бренды по названию

Популярные бренды