Sirona XIOS XG Select Скачать руководство пользователя страница 97

Страница: 97 / 120

Sirona Dental Systems GmbH
Gebrauchsanweisung und Installation

5 Operation

64 08 137 D3610
D3610.201.02.09.02 11.2017

5.9.2

With Aimright reusable sensor holder system

NOTICE

The sensor cable is sensitive to mechanical influences.

The cable may become damaged or may wear out prematurely.
➢ Do not pull on the sensor cable when pulling the sensor out of the

hygienic protective sleeve. Slide the sensor further out of the
hygienic protective sleeve with your thumb as described below.

➢ Avoid bending, creasing or rotating the cable or exposing it to

other strains.

Remove the sensor with the hygienic protective sleeve from the
sensor holder. To do this, open up the sensor holder by pressing
gently on one side as shown in the figure.

Carefully push the sensor out of the narrow part of the hygienic
protective sleeve with two fingers.

Slide the sensor further out of the hygienic protective sleeve.

Hold on to the sensor and remove it from the hygienic protective
sleeve.

Содержание XIOS XG Select

























































































































Результаты поиска

Содержание XIOS XG Select

Отзывы:

Похожие инструкции для XIOS XG Select

Бренды по названию

Популярные бренды

Sirona XIOS XG Select, Инструкция по эксплуатации и установке

Результаты поиска

Содержание XIOS XG Select

Отзывы:

Похожие инструкции для XIOS XG Select

Бренды по названию

Популярные бренды