Sirona XIOS XG Select Скачать руководство пользователя страница 88

Страница: 88 / 120

5 Operation

Sirona Dental Systems GmbH

Gebrauchsanweisung und Installation

64 08 137 D3610

D3610.201.02.09.02 11.2017

5.6.2.3

Horizontal bite wing exposures

Preparing the sensor holder

For bite wing exposures use the red sensor holder.

Fasten the guide rod for the sensor (C) in the perforation (B) of the
localizer ring (A).

Slide the sensor into the hygienic protective sleeve, see section
"Slide the hygienic protective sleeve over the sensor".

Place the sensor on the palm of your hand and clip the sensor
holder onto the sensor.

Slide the sensor into the center of the sensor holder.

Position the sensor

Look through the localizer ring to check the alignment of the sensor.
The sensor must be located centrally in front of the opening in the
localizer ring.

Содержание XIOS XG Select

























































































































Результаты поиска

Содержание XIOS XG Select

Отзывы:

Похожие инструкции для XIOS XG Select

Бренды по названию

Популярные бренды

Sirona XIOS XG Select, Инструкция по эксплуатации и установке

Результаты поиска

Содержание XIOS XG Select

Отзывы:

Похожие инструкции для XIOS XG Select

Бренды по названию

Популярные бренды