Silicon Graphics InfiniteStorage 4000 Series Скачать руководство пользователя страница 25

Страница: 25 / 276

Chapter 1: About the Command Line Interface

Set Storage Array
AutoSupport Bundle
Disable

This command turns off the AutoSupport (ASUP) bundle collection and transmission

for the storage array. You can run this version of the command from the script editor

or in a script file.

Syntax

set storageArray autoSupport disable

Parameters

None.

Minimum Firmware Level

7.86

Set Storage Array
AutoSupport Bundle
Enable

This command turns on the AutoSupport (ASUP) bundle collection and transmission

for the storage array.

Syntax

set storageArray autoSupport enable

Parameters

None.

Minimum Firmware Level

7.86

Test AutoSupport
Configuration

NOTE

This command is an SMcli command, no

a script command. You must run this

command from a command line. You cannot run this command from the script editor

in the storage management software

This command validates the current auto support configuration by sending a test

ASUP bundle and reports the result of the test transmission.

Syntax

SMcli -supportBundle testConfig

Parameters

None

Minimum Firmware Level

7.86

Содержание InfiniteStorage 4000 Series




















































































































































































































































































Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание

Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды