Silicon Graphics InfiniteStorage 4000 Series Скачать руководство пользователя страница 21

Страница: 21 / 276

Chapter 1: About the Command Line Interface

Alert Severities
Commands

The CLI provides special commands that enable you to set alert severities, and to send

out a test alert to the Windows Event Log and all configured syslog receivers. The

alert severities apply to all of the storage arrays in the entire storage system. The

commands are SMcli commands that run only from a command line.

Setting Alert Severities

SMcli -alertSeverities (

severity



[

severity1

, ...

severityN

])

You can set the following alert severities:



critical

– Alerts will be sent



warning

– Alerts will be sent



informational

– Alerts will not be sent



debug

– Alerts will be sent

NOTE

The debug value is for Technical Support only. Do not attempt to use this value.

You can set one or more alert severities values. If you set more than one alert

severities value, enclose all of the values in square brackets ([ ])and separate the

values by a comma.

Showing Alert Severities

SMcli -alertSeverities

This command shows all of the severities for which an alert is sent. This command

cannot show information for a specific type of severity.

Sending a Test Alert

SMcli -alertTest

-w

Specifies the WWID of the storage array. This terminal is an alternate to the

-n

terminal. Use the

-w

terminal with the

-d

terminal to show the WWIDs

of the known storage arrays. The file content has this format:

storage-system-name world-wide-ID IP-address1

IP-address2

-X

(uppercase)

Deletes a storage array from a configuration.

-x

(lowercase)

Removes an SNMP trap destination or an email address alert destination.

The

community

is the SNMP community name for the trap, and the

host

is the IP address or DNS host name of the system to which you want the trap

sent.

Shows usage information about the CLI commands.

Terminal

Definition

Содержание InfiniteStorage 4000 Series




















































































































































































































































































Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание

Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды