manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание


Поделиться
Скачать
background image

184

Routine Maintenance 

To clear persistent volume reservations, use this command:

clear (allVolumes | volume [

volumeName

] | 

volumes [

volumeName1

 ... 

volumeNameN

]) reservations

Synchronizing the 
Controller Clocks

To synchronize the clocks on both controllers in a storage array with the host clock, 

use this command:

set storageArray time

Locating Drives

At times, you might need to locate a specific drive. In very large storage array 

configurations, this task can sometimes be awkward. If you need to locate a specific 

drive, you can do so by turning on the indicator light on the front of the drive. To 

locate a drive, use this command:

start drive [

trayID

,

slotID

] locate

To turn off the indicator light after locating the drive, use this command:

stop drive locate

Relocating a Volume 
Group

Volume group relocation describes the action of moving drives within the same 

storage array. This is a supported capability; however, any relocation of storage array 

components must be completed under the guidance of your Technical Support 

representative.
This section describes the commands that you use to remove a set of drives and then 

reinstall them into a different storage array. 

Hot and Cold Volume Group Relocation

There are two methods you can use to move volume groups: hot volume group 

relocation and cold volume group relocation.

Hot volume group relocation lets you add or move storage without reconfiguring 

the storage array and, in some cases, without rebooting. During hot volume group 

relocation, the storage array power is not turned off.

Cold volume group relocation requires that the power to the source storage array 

and the destination storage array be turned off before moving the volume groups 

from one storage array to another. Then the power to the storage arrays can be 

turned on.

To make sure that any volume group being moved to a different destination storage 

array is correctly recognized and managed by the new storage array, use hot volume 

group relocation whenever possible.

ATTENTION  Possible loss of data access

 – You must move a single volume group 

at a time, and it must go into a storage array with the same level of controller firmware.

Содержание InfiniteStorage 4000 Series





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage 4000 Series

D-Link DES-7200 User Manual preview
DES-7200
Бренд: D-Link Страницы: 100
D-Link DES-3226L Manual preview
DES-3226L
Бренд: D-Link Страницы: 134
D-Link DES-3010F Command Line Interface Manual preview
DES-3010F
Бренд: D-Link Страницы: 187
D-Link DES-3010F Manual preview
DES-3010F
Бренд: D-Link Страницы: 225
D-Link DES-1048G Manual preview
DES-1048G
Бренд: D-Link Страницы: 31
D-Link DES-1050G User Manual preview
DES-1050G
Бренд: D-Link Страницы: 35
D-Link DES-1016D - Switch Quick Install Manual preview
DES-1016D - Switch
Бренд: D-Link Страницы: 19
D-Link COVR-2202 User Manual preview
COVR-2202
Бренд: D-Link Страницы: 107
D-Link AirPlusXtremeG DI-624 Troubleshooting preview
AirPlusXtremeG DI-624
Бренд: D-Link Страницы: 5
D-Link DGS-1210-28P Getting Started Manual preview
DGS-1210-28P
Бренд: D-Link Страницы: 48
D-Link DSL-2640BT Installation Manual preview
DSL-2640BT
Бренд: D-Link Страницы: 12
NEC Express5800/T110g-E Quick Start Manual preview
Express5800/T110g-E
Бренд: NEC Страницы: 2
Qsan Technology XCubeSAN XS5224D Hardware Manual preview
XCubeSAN XS5224D
Бренд: Qsan Technology Страницы: 143
LaCie 4big Spare Drive Quick Install Manual preview
4big Spare Drive
Бренд: LaCie Страницы: 24
HPE ProLiant DL180 Gen10 Product End-Of-Life Disassembly Instructions preview
ProLiant DL180 Gen10
Бренд: HPE Страницы: 10
Oracle DE2-24 Customer Service Manual preview
DE2-24
Бренд: Oracle Страницы: 312
IBM eServer 342 xSeries Installation Manual preview
eServer 342 xSeries
Бренд: IBM Страницы: 70
NETGEAR WAG302 Installation Manual preview
WAG302
Бренд: NETGEAR Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды