manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание


Поделиться
Скачать
background image

Chapter 3: Configuration Concepts

37

3

Configuration Concepts

When you configure a storage array, you organize drives into a logical structure that 

provides storage capacity and data protection so that one or more hosts can safely 

store data in the storage array. This chapter provides definitions of the physical and 

logical components required to organize the drives into a storage array configuration. 

This chapter also describes how the components relate to each other.
Before you begin to configure your storage array, become familiar with these 

concepts:

Controllers

Drives

Hot spares

Volume groups

Disk Pools

Volumes

RAID technology

Hosts

Host groups

Host bus adapter (HBA) host ports

Logical unit numbers (LUNs)

Configuring a RAID storage array requires caution and planning to make sure that 

you define the correct RAID level and the configuration for your storage array. The 

main purpose in configuring a storage array is to create volumes, which are 

addressable by the hosts, from a collection of drives. The commands described in the 

following chapters enable you to set up and run a RAID storage array. Additional 

commands also are available to provide you with more control and flexibility in 

managing and maintaining your storage array.

Controllers

All storage arrays have one or two controllers. The controllers are circuit-board 

assemblies that manage data flow and communications between the hosts and the 

drives in the storage array, keeping track of the logical addresses of where the data 

resides. In general, each controller has a processor for performing control operations, 

NVSRAM for storing the firmware code that operates the storage array, and the buses 

along which the data flows.
The controllers are located in a controller tray or a controller-drive tray. A controller 

tray or a controller-drive tray has two positions for controllers: slot A and slot B. The 

script commands identify each controller by the slot in which the controller is 

installed. If a controller tray or a controller-drive tray has only one controller, the 

Содержание InfiniteStorage 4000 Series





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage 4000 Series

D-Link NetDefend DFL-260E Reference Manual preview
NetDefend DFL-260E
Бренд: D-Link Страницы: 328
D-Link DFL-210 - NetDefend - Security Appliance Firewall Registration Manual preview
DFL-210 - NetDefend - Security Appliance
Бренд: D-Link Страницы: 19
Dahua N300 Quick Start Manual preview
N300
Бренд: Dahua Страницы: 12
D-Link NetDefend DFL-1600 Quick Manual preview
NetDefend DFL-1600
Бренд: D-Link Страницы: 23
D-Link DWR-112 Technical Support Setup Procedure preview
DWR-112
Бренд: D-Link Страницы: 11
D-Link DSR-250 Cli Reference Manual preview
DSR-250
Бренд: D-Link Страницы: 83
D-Link DSR-150 Reference Manual preview
DSR-150
Бренд: D-Link Страницы: 129
D-Link DSL-G804V Manual preview
DSL-G804V
Бренд: D-Link Страницы: 10
D-Link DSL-G804V Quick Information Manual preview
DSL-G804V
Бренд: D-Link Страницы: 21
D-Link DSL-2750E Quick Start Manual preview
DSL-2750E
Бренд: D-Link Страницы: 6
D-Link DSL-2750E Technical Support Setup Procedure preview
DSL-2750E
Бренд: D-Link Страницы: 17
D-Link DSL-2740U Setup Manual preview
DSL-2740U
Бренд: D-Link Страницы: 4
D-Link DSL-2730B How To Set Up preview
DSL-2730B
Бренд: D-Link Страницы: 6
D-Link DSL-520T Quick Installation Manual preview
DSL-520T
Бренд: D-Link Страницы: 86
D-Link DSL-502T Installing Usb Drivers preview
DSL-502T
Бренд: D-Link Страницы: 3
D-Link DSL-3900 Quick Start Manual preview
DSL-3900
Бренд: D-Link Страницы: 4
D-Link DWR-921 How To Set Up preview
DWR-921
Бренд: D-Link Страницы: 4
D-Link DSL-3580L Series Quick Installation Manual preview
DSL-3580L Series
Бренд: D-Link Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды