Silicon Graphics InfiniteStorage 4000 Series Скачать руководство пользователя страница 51

Страница: 51 / 276

Chapter 3: Configuration Concepts

Figure 1 Drive Drawer with Drives

The total number of drives in a storage array depends on the model of the controller

tray or controller-drive tray and the capacity of the drives. The following table lists,

by controller tray or controller-drive tray model and drive tray capacity, the maximum

number of drives in a storage array.

NOTE

A maximum of seven drive trays can be on a channel when mixing 14-slot

drive trays and 16-slot drive trays.

The maximum capacity in a storage array depends on the number of the drives in the

storage array and the capacity of each drive in the storage array. The following table

lists the maximum storage for each controller model based on the capacity of the

drives.

Hot Spare
Drives

NOTE

Hot spare drives works only on storage arrays configured to use volume

groups.

A hot spare is a drive that acts as a standby in the event that a drive containing data

fails. The hot spare is a drive that has not been assigned to a particular volume group

and, as such, can be used in any volume group. You can use the hot spare feature with

RAID Level 1, RAID Level 3, RAID Level 5, or RAID Level 6. If a drive in a volume

group fails, the controllers automatically replace the failed drive with a hot spare. The

controllers use redundancy data to reconstruct the data from the failed drive onto the

hot spare. To be most effective, the drive that you assign as a hot spare must have a

capacity equal to or greater than the capacity of the largest drive in the storage array.

Содержание InfiniteStorage 4000 Series




















































































































































































































































































Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание, Страница: 51 / 276

Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы: