Silicon Graphics InfiniteStorage 4000 Series Скачать руководство пользователя страница 198

Страница: 198 / 276

186

Performance Tuning

Table 25 Information About Storage Array Performance

The command takes this form:

save storageArray performanceStats file=”

filename

”

where

filename

is the name of the file in which you want to save the performance

statistics. You can use any file name that your operating system can support. The

default file type is

.csv

. The performance information is saved as a

comma-delimited file.
Before you use the

save storageArray performanceStats

command, run

these commands to specify how often statistics are collected.



set session performanceMonitorInterval



set session performanceMonitorIterations

Type of Information

Description

Devices

These devices are included in the file:



Controllers

– The controller in slot A or slot B and a list of the

volumes that are owned by the controller



Volumes

– A list of the volume names



Storage array totals

– A list of the totals for both controllers in an

active/active controller pair, regardless if one, both, or neither are

selected for monitoring

Total I/Os

The number of total I/Os performed since the storage array was started

Read Percentage

The percentage of total I/Os that are read operations (calculate the

write percentage by subtracting the read percentage from 100 percent)

Cache Hit Percentage

The percentage of reads that are fulfilled by data from the cache rather

than requiring an actual read from a drive

Current KB per second

The current transfer rate in kilobytes per second (current means that the

number of kilobytes per second since the last time that the polling

interval elapsed, causing an update to occur)

Maximum KB per second The highest data transfer value that is achieved in the current

kilobyte-per-second statistic block

Current I/O per second

(IOPS)

The current number of I/Os per second (current means the number of

I/Os per second since the last time that the polling interval elapsed,

causing an update to occur)

Maximum I/O per second The highest number of I/Os achieved in the current I/O-per-second

statistic block

Содержание InfiniteStorage 4000 Series




















































































































































































































































































Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание

Результаты поиска

Содержание InfiniteStorage 4000 Series

Отзывы:

Похожие инструкции для InfiniteStorage 4000 Series

Бренды по названию

Популярные бренды