manualshive.com logo in svg

Silicon Graphics InfiniteStorage 4000 Series, Настройка и обслуживание


Поделиться
Скачать
background image

Chapter 11: Maintaining a Storage Array

199

Taking a controller offline can seriously impact data integrity and storage array 

operation.

If you do not use write cache mirroring, data in the cache of the controller you 

place offline is lost.

If you take a controller offline and you have controller failover protection through 

a host multi-path driver, the other controller in the pair takes over. Volume groups 

and their associated volumes that were assigned to the offline controller are 

automatically reassigned to the remaining controller. If you do not have a 

multi-path driver installed on the application host and you take a controller 

offline while the application is using associated volumes, application errors will 

occur.

ATTENTION  Possible loss of data access

 – Placing a controller offline can cause 

loss of data.

Use Service mode to replace canisters, such as a controller. Placing a controller in 

Service mode makes it unavailable for I/O operations and moves its volume groups to 

the second controller without affecting the preferred path of the volume group. This 

action might significantly reduce performance. The volume groups are automatically 

transferred back to the preferred controller when it is placed back online.
If you change a controller to Service mode while an application is using the 

associated volumes on the controller, the change causes I/O errors unless a multi-path 

driver is installed on the host. Before you place a controller in Service mode, make 

sure that the volumes are not in use, or a multi-path driver is installed on all of the 

hosts that are using these volumes.
In addition, if you do not have a multi-path driver, you must make appropriate 

operating system-specific modifications to make sure that the volume groups moved 

are accessed on the new path when you change to Service mode.

NOTE  

Place a controller in Service mode only under the direction of a Technical 

Support representative.

To change the operational mode of a controller, use this command:

set controller [(a | b)] availability=(online | 

offline | serviceMode)

Содержание InfiniteStorage 4000 Series





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для InfiniteStorage 4000 Series

TANDBERG VCS Administrator'S Manual preview
VCS
Бренд: TANDBERG Страницы: 276
IBM Redbooks ServeRAID-MR10k User Manual preview
Redbooks ServeRAID-MR10k
Бренд: IBM Страницы: 48
IBM System Storage DS4000 Hardware Maintenance Manual preview
System Storage DS4000
Бренд: IBM Страницы: 184
XAVI Technologies Corp. 7721r User Manual preview
7721r
Бренд: XAVI Technologies Corp. Страницы: 71
Fortinet FortiAP S311C Quick Start Manual preview
FortiAP S311C
Бренд: Fortinet Страницы: 20
I-O Wireless WBC11 User Manual preview
WBC11
Бренд: I-O Wireless Страницы: 55
Ruckus Wireless MediaFlex NG Quick Installation Manual preview
MediaFlex NG
Бренд: Ruckus Wireless Страницы: 2
Rosewill RNX-N150RT Quick Installation Manual preview
RNX-N150RT
Бренд: Rosewill Страницы: 10
SanDisk 175972 User Manual preview
175972
Бренд: SanDisk Страницы: 2
QNAP TS-h1677XU-RP Quick Installation Manual preview
TS-h1677XU-RP
Бренд: QNAP Страницы: 7
TP-Link TD-W8101G Quick Installation Manual preview
TD-W8101G
Бренд: TP-Link Страницы: 16
Handicare DX REM 420 User Manual preview
DX REM 420
Бренд: Handicare Страницы: 60
Zalip CDE570AM-U User Manual preview
CDE570AM-U
Бренд: Zalip Страницы: 76
DHD Power Cruiser 52/XR Manual preview
52/XR
Бренд: DHD Power Cruiser Страницы: 60
Nexxt Amp300 Quick Installation Manual preview
Amp300
Бренд: Nexxt Страницы: 2
Atlantis Land Edge-Core A07-ES4548C Specification Sheet preview
Edge-Core A07-ES4548C
Бренд: Atlantis Land Страницы: 2
OWC MERCURY ELITE PRO MINI Manual preview
MERCURY ELITE PRO MINI
Бренд: OWC Страницы: 8
xFusion Digital Technologies FusionServer 1288H V5 Technical Paper preview
FusionServer 1288H V5
Бренд: xFusion Digital Technologies Страницы: 96

Бренды по названию

Популярные бренды

Загрузить еще бренды