Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 96

Страница: 96 / 164

Siemens Flow Instruments Modbus RTU specification for add-on modules
Number of stations

Recommended: max. 31 per segment without repeaters

Device address range

1 to 247

Protocol

RTU
(Other Modbus protocols like ASCII, Plus or TCP/IP are not supported)

Electrical interface

RS 485, 2-wire and RS 232, 2-wire

Connecter type

Screw terminals

Supported function codes

read coils

read holding registers

write single coil

16:

write multiple registers

17:

report slave ID

Broadcast

Yes

Maximum cable length

1200 meters (@38 400 bits/sec.)

Standard

Modbus over serial line v1.0

Certified

Device profile

None

Add-on modules comply with

MODBUS over serial line specification & implementation guide v. 1.0
modbus.org 12/02/02
MODBUS application protocol specification v. 1.1
modbus.org 12/06/02

Isolation

500 V AC functional isolation of data signals and common

Add-on modules must be connected to equipment complying with "Low Voltage Directive" in

order to be considered safe. The isolation within the MAG 8000 and MAG 8000 CT add-on

MODBUS module is only functional isolation.

10.6

Output characteristics

This chapter describes how the MAG 8000 and MAG 8000 CT outputs work.

Technical data
10.6 Output characteristics

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы:

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 96 / 164

Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы: