Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 19

Страница: 19 / 164

Inlet and outlet condition

To achieve most accurate flow measurement it is essential to have certain straight inlet and

outlet pipe lengths as shown (D

: sensor diameter). MAG 8000 CT is approved for installation

with 0D of straight pipe upstream from the sensor and 0D of straight pipe downstream from

the sensor. It is, however, recommended to follow the installation guidelines for the MAG 8000

Standard water meter for optimal measurement performance.

Sensor must be completely full of liquid

Therefore avoid:
● Air in pipe.
● Installation at the highest point in pipe system.
● Installation in vertical pipes with free outlet.

Installing/Mounting

4.1 Sensor installation

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы:

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 19 / 164

Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы: