Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 25

Страница: 25 / 164

4.2

Potential equalization

Liquid potential equalization or grounding is accomplished with built-in grounding electrodes

and/or grounding rings. The electrodes ensure electrical connection between liquid and meter

providing a stable and accurate measurement.

①

Built-in grounding electrode

(7ME6810 and 7ME6820)

②

Grounding rings pre-mounted on

MAG 8000 Irrigation (7ME6880)

4.3

Grounding

The sensor body must be grounded using grounding/bonding straps and/or grounding rings

to protect flow signal against stray electrical noise and/or lightning. This ensures that noise is

carried through sensor body and that the measuring area within sensor body is noise-free.

Irrigation applications

MAG 8000 Irrigation device is always delivered with pre-mounted grounding rings. Grounding

rings are mandatory for MAG 8000 Irrigation.

Installing/Mounting

4.3 Grounding

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы:

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 25 / 164

Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы: