Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 18

Страница: 18 / 164

4.1

Sensor installation

The sensor installation consists of three steps:
1. Locating the sensor.
2. Orienting the sensor.
3. Mounting the sensor.

4.1.1

Locating the sensor

Ensure that the sensor is located in the most optimum place and where no magnetic field is

present.

87L

166

Flow direction

Ensure that sensor is mounted in correct flow direction as indicated on label.

)ORZ

GLUHFWLRQ

If process flow direction is opposite of flow direction indicated on sensor label, forward flow

rates can be restored via parameter 327, if factor is adjusted to "-1".
MAG 8000 CT is approved for bidirectional measurement.

Installing/Mounting
4.1 Sensor installation

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы:

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 18 / 164

Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы: