Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 164

Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 7

Introduction

1

These instructions contain all the information you need for using the device.
The instructions are aimed at persons mechanically installing the device, connecting it

electrically, configuring the parameters and commissioning it, as well as service and

maintenance engineers.

Note
It is the responsibility of the customer that the instructions and directions provided in the

operating instructions are read, understood, and followed by the relevant personnel before

installing the device.

1.1

Items supplied

● SITRANS F M MAG 8000 Standard, MAG

8000 CT, or MAG 8000 Irrigation

● Calibration certificate
● Operating Instructions
● SITRANS F M documentation disk

Inspection

1. Check for mechanical damage due to possible improper handling during shipment. All

claims for damage are to be made promptly to the shipper.

2. Make sure the items supplied, and the information on the nameplate corresponds to the

ordering information.

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

7

«
...
5
6
7
8
9
...
»

Содержание SITRANS F M MAG 8000





































































































































































Отзывы:

Нет отзывов