Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 128

Страница: 128 / 164

A.9

Battery configuration

Battery figures (generated as customer parameter list, see section Customer-selected

parameter list in chapter Setting the basic parameters show power management information.

Figure A-5

Battery configuration

At each battery replacement the capacity is reset to 100% (parameters 508 to 510) which is

then reduced with the real meter consumption every 4 hours.
The battery limit (parameter 206) is the level at which the low power alarm is activated

generating an alarm or call-up (if configured). The power status (parameter 513) follows the

battery symbol on the display.
When switching between battery power from internal and external battery packs, "Battery

power" (parameter 507) must be adjusted to match the actual number of batteries connected.

Flow Tool
A.9 Battery configuration

SITRANS MAG 8000

128

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы:

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 128 / 164

Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы: