manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 38 / 164

Поделиться
Скачать
Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 38

RS 485 connection diagram

①

Common

②

Connect shield to encapsulation

③

Shield must be connected to protective ground

①

Common

②

Termination

A Modbus RS 485 must use a balanced pair (for D+ - D−) and a third wire (for common).
For the balanced pair used in an RS 485 system, a characteristic impedance with a value 

between 100 and 120 ohms must be used.
Shield must always be connected to MAG 8000 encapsulation using cable clamp as shown in 

figure in section cable installation, see Power supply (Page 34).
Bus termination:
All RS 485-based networks must be terminated correctly to function properly. A termination 

must be placed at each end of segment.
The Modbus RTU module can add a 120 ohm termination if a jumper is placed beside terminals 

in position "ON".
Termination is set to "ON" from factory.

Connecting
5.5 Communication modules

SITRANS MAG 8000

38

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Отзывы:

Нет отзывов