Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 35

Страница: 35 / 164

Battery backup input

Male battery connector with black and red wires; black wire is ground. Male battery connector

has to be connected to female connector on backup battery

Functional ground

Black wire with terminal must be connected to the device encapsulation with a screw

Cable installation

Choose the correct glands for the selected cable type, see Accessories (Page 157) for glands

selection. Ensure shield is mounted under cable clamps - do not make pig tails.

Note
Mains or line-powered PUR cable (no shield) has to be mounted under cable clamps. All cable

glands have to be sufficiently tightened to ensure IP-rating.

Connecting

5.3 Power supply

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы:

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 35 / 164

Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы: