Siemens SIRIUS 3RW5 series Скачать руководство пользователя страница 75

Страница: 75 / 214

Error type

Inter‐
rupt
type

Error / Warning

Cause

+ F

Byte.Bit

0x1021

Asymmetry

A limit value for asymmetry has been exceeded.
Asymmetry can cause an overload.
• Phase failure.
• Fault in the motor windings.

14.0

0x1021

62.6

0x1022

Therm. motor model over‐
load

• The motor feeder has been overloaded.
• The motor temperature rise has exceeded a lim‐

it.

12.3

0x1022

62.3

0x1024

Temperature sensor over‐
load

The temperature of the motor is too high.

12.0

0x1024

22.5

0x1025

Temperature sensor short
circuit

A short circuit has occurred in the temperature sen‐
sor cable.

12.2

0x1025

22.7

0x1026

Temperature sensor wire
break

A wire has broken in the sensor cable of the tem‐
perature sensor.

12.1

0x1026

22.6

0x1027

Ground fault

The ground-fault monitoring has responded. An
impermissibly high residual current is flowing.

16.0

0x1027

62.7

0x1033

No start-up data received

Data necessary for device start-up are missing.

18.4

0x1034

Starting time exceeded

The set maximum starting time is shorter than the
starting time required by the motor.

92.2

0x1035

Starting time undershot

The set minimum starting time is longer than the
starting time required by the motor.

92.3

0x1036

Parameters for Ex motor pro‐
tection received

Parameters for the EX motor protection have been
received.

60.2

0x1040

Threshold I exceeded

The current has exceeded a limit.

14.2

0x1040

62.4

0x1041

Threshold I undershot

The current has undershot a limit.

14.3

0x1041

62.5

0x1042

Threshold P exceeded

The active power of the motor has exceeded a limit
value.

83.2

0x1042

83.4

0x1043

Threshold P undershot

The active power of the motor has undershot a limit
value.

83.3

0x1043

83.5

0x1046

Actuator disconnection

The module has disconnected the actuator. An ad‐
ditional diagnostic message will be displayed to
provide you with more detailed information about
the cause.

12.4
14.1
14.4
83.6

0x1057

Number of switch-on opera‐
tions exceeded

The permissible number of switch-on operations in
the monitoring period has been exceeded.

71.1

0x1057

71.3

0x1080

Device error

Irrecoverable error detected following self-diagnos‐
tics (self-test, contactor contacts, switching ele‐
ment, etc.).

19.2

0x1081

Bypass defective

• Bypass defective
• The error can also be generated by successive,

brief interruptions of the control supply voltage.

29.3

Messages and diagnostics

7.2 Diagnostics via configuration software of the controller

SIRIUS 3RW5 PROFINET communication modules
Equipment Manual, 05/2021, A5E35631297002A/RS-AD/004

Содержание SIRIUS 3RW5 series























































































































































































































Результаты поиска

Содержание SIRIUS 3RW5 series

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIRIUS 3RW5 series, Руководство по эксплуатации оборудования

Результаты поиска

Содержание SIRIUS 3RW5 series

Отзывы:

Бренды по названию

Популярные бренды