manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 3 / 128

Поделиться
Скачать
Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 3

Contents

0 - 3

Siemens AG

 

SPR2-230.061.01

Page  3 of  8

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

 

1 _______Prerequisites __________________________________________________ 1 - 1

Required documents   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1 - 1
Required tools, measurement and auxiliary devices   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1 - 1
Information regarding this document  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1 - 2

Position designations  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1 - 2

Safety Information .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1 - 3

Notes on the protective conductor resistance test .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1 - 7
Notes on device leakage current measurement .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1 - 8

Basic system   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 11

Removing the cover  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 11
Installing the cover.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 11

Cover over the horizontal carriage   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 12

Removing the cover  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 12
Attaching the cover   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 13
SIREPHOS cover  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 14

Monitor trolley  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 15

Removing the covers   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 15
Installing the covers  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 16

Installing/removing the cover at the C-arm mounting  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 16
Telescoping cover underneath the horizontal carriage   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 16
I.I. service position   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 17

Moving the I.I. into the service position  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 17
Installing the I.I.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 17

Concluding steps  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1 - 18

2 _______Line voltage adjustment _________________________________________ 2 - 1

Checking the line voltage on the monitor trolley .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2 - 1

3 _______Checking the operating voltages __________________________________ 3 - 1

Low voltages.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3 - 1
I.I. Voltages  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .    . 3  -  1

4 _______Loading the operating software ___________________________________ 4 - 1

Control board D1, Host  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 - 1
Storage of the error log as ASCII file  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 - 1
Option 3D Reconstruction, Trace File and Event Log File.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 - 2

Saving trace files   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 - 2
Saving current trace files directly after display of an error .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 - 3

5 _______Adjustments / Programs _________________________________________ 5 - 1

Checking the generator adjustment .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5 - 3
Dose rate adjustment  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5 - 5

Prerequisites.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5 - 5

Page

Содержание SIREMOBIL Iso-C

































































































































Отзывы:

Нет отзывов