manualshive.com logo in svg

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 38 / 128

Поделиться
Скачать
Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 38

SIREMOBIL Iso-C

 

SPR2-230.061.01

Page 2 of 30

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

5 - 2

Adjustments / Programs

 

Generator Adjustment (Filament circuit learning program)

•

Connect the service PC to the serial interface on board D1.

•

Start the service program.

•

Select the Diagnostic menu.

•

Select the Monitoring menu.

•

In the "Group 1" Combo box, select "Generator adjustment".

•

Click on "Update Start".

•

After the "Start fluoro" message in the ACTIONS line, press the radiation release button 
on the SIREMOBIL Iso-C hand switch. 

•

Continue to hold the radiation release button as long as the message "Continue fluoro" is 
displayed in the ACTIONS line.

•

"Warmup" appears in the STATUS line, the SIREPHOS is warming up.

•

After approximately 8 minutes, the message "learning pushfactor" will appear in the 
STATUS line.

•

A maximum of 15 exposures will automatically be released.

•

The message "Learning done" appears in the STATUS line after the generator adjust-
ment has been successfully completed.

•

The "Stop monitoring" message appears in the ACTIONS line.

•

Activate the radiation release button. 

•

Click on "Update Stop".

The kV offset adjustment must be performed prior to starting the 
generator adjustment.

If an error occurs during the generator adjustment, switch OFF 
the SIREMOBIL Iso-C and perform the kV Offset and generator 
adjustments again.

As soon as the generator adjustment is started, press the radia-
tion release button on the hand switch until the "Stop monitoring" 
message appears in the ACTIONS line. If you deactivate radiation 
too soon, the generator adjustment must be completely repeated.
Exception: You can briefly stop pressing the radiation release 
button (less than 30 seconds) during the warmup phase (warmup 
displays in the STATUS line on the service PC) of the SIREPHOS. 
The generator adjustment continues when the radiation release 
button is pressed again.

X-ray radiation!
See Chapter 1, Safety Information.

Observe the need for radiation protection. Wear a lead apron.

NOTE

NOTE

NOTE

WARNING

Содержание SIREMOBIL Iso-C

































































































































Отзывы:

Нет отзывов