Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 79

Страница: 79 / 128

Replacing boards / replacing components

6 - 13

Siemens AG

SPR2-230.061.01

Page 13 of 48

SIREMOBIL Iso-C

Medical Solutions

Rev. 13

12.04

CS PS 24

System Manual

Removal

VIDEOMED DC

•

Move the I.I. into the service position. Refer to chapter 1, I.I. service position.

•

Remove the Videomed DC and place it on a clean surface.

•

Cover it to prevent contamination. Refer also to chapter 6, VIDEOMED DC.

I.I. mini voltage supply

•

Remove the I.I. mini voltage supply and lay it down on a suitable surface
(Control section and high voltage section).

•

Refer to chapter 6, Replacing the I.I. mini voltage supply.

•

Dissipate any residual voltage in the cables by shorting them to ground.

•

Remove the O-ring and the cap nut from the anode cable.

•

Remove the plug for the cassette contact.

•

Disconnect all the cables (protective conductor, cable to VIDEOMED DC, etc.....) from
the I.I.

•

At the same time, remove the cable ties or the cable clamps.

•

Pull all the cables inside the C-arm.

Risk of injuries on mechanical parts!
If not observed, slight to medium injuries, especially to the hands,
can occur.

Observe the notes concerning the C-arm carbon fiber structure.

Risk of injury!
Noncompliance can lead to light to medium injuries and/or
property damage.

The C-arm covers contain counterbalance weights and weigh
approx. 6 kg.
Hold the covers firmly when installing or removing them.

Before the C-arm cover will be loosened, the C-arm must be
moved to its middle orbital position.
If the C-arm covers are loosened, the C-arm may not be moved to
its orbital end positions (I.I. or SIREPHOS at the orbital end posi-
tion).

WARNING

CAUTION

Содержание SIREMOBIL Iso-C

































































































































Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы:

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 79 / 128

Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы: